Project

General

Profile

HDMI Output splash screen is intermittently displayed on ... » no_timeouts_no_splash.log

Did not see timeouts but splash screen did not appear - Stephen Snyder, 08/09/2016 09:43 AM

 
1
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2016.08.09 09:31:58 =~=~=~=~=~=~=~=~=~=~=~=
2

3
U-Boot SPL 2013.01.01 (May 16 2016 - 18:37:05)
4
BOARD : Critical Link MitySOM-5CSx Module
5
CLOCK: EOSC1 clock 25000 KHz
6
CLOCK: EOSC2 clock 25000 KHz
7
CLOCK: F2S_SDR_REF clock 0 KHz
8
CLOCK: F2S_PER_REF clock 0 KHz
9
CLOCK: MPU clock 800 MHz
10
CLOCK: DDR clock 400 MHz
11
CLOCK: UART clock 100000 KHz
12
CLOCK: MMC clock 50000 KHz
13
CLOCK: QSPI clock 400000 KHz
14
RESET: COLD
15
INFO : Watchdog enabled
16
SDRAM: Initializing MMR registers
17
SDRAM: Calibrating PHY
18
SEQ.C: Preparing to start memory calibration
19
SEQ.C: CALIBRATION PASSED
20
SDRAM: 1024 MiB
21
SDRAM: Scrubbing 0x01000000 - 0x02000000
22
SDRAM: Scrubbing success with 23 ms
23
SDRAM: Scrubbing 0x00000000 - 0x01000000
24
SDRAM: Scrubbing 0x02000000 - 0x40000000
25
SDRAM: ECC Enabled
26
ALTERA DWMMC: 0
27
SDRAM: Scrubbing success with consuming additional 1426 ms
28

    
29

    
30
U-Boot 2013.01.01 (May 16 2016 - 18:37:12) Critical Link MitySOM-5CSx
31

    
32
CPU   : Altera SOCFPGA Platform
33
BOARD : Critical Link MitySOM-5CSx Module
34
I2C:   ready
35
DRAM:  1 GiB
36
MMC:   ALTERA DWMMC: 0
37
In:    serial
38
Out:   serial
39
Err:   serial
40
Net:   mii0
41
gpio: pin 28 (bank/mask = 0/0x10000000)
42
gpio: pin 28 (gpio 28) value is 0
43
gpio: pin 28 (bank/mask = 0/0x10000000)
44
gpio: pin 28 (gpio 28) value is 1
45
gpio: pin 0 (bank/mask = 0/0x00000001)
46
gpio: pin 0 (gpio 0) value is 1
47
gpio: pin 9 (bank/mask = 0/0x00000200)
48
gpio: pin 9 (gpio 9) value is 0
49
gpio: pin 9 (bank/mask = 0/0x00000200)
50
gpio: pin 9 (gpio 9) value is 1
51
Hit any key to stop autoboot:  5  4  3  2  1  0 
52
3724376 bytes read in 232 ms (15.3 MiB/s)
53
21838 bytes read in 37 ms (576.2 KiB/s)
54
7007204 bytes read in 393 ms (17 MiB/s)
55
## Starting application at 0x3FF7770C ...
56
## Application terminated, rc = 0x0
57
## Starting application at 0x3FF7770C ...
58
## Application terminated, rc = 0x0
59
## Booting kernel from Legacy Image at 00007fc0 ...
60
   Image Name:   Linux-3.16.0-00291-gc24173f
61
   Image Type:   ARM Linux Kernel Image (uncompressed)
62
   Data Size:    3724312 Bytes = 3.6 MiB
63
   Load Address: 00008000
64
   Entry Point:  00008000
65
## Flattened Device Tree blob at 00000100
66
   Booting using the fdt blob at 0x00000100
67
   XIP Kernel Image ... OK
68
OK
69
   Loading Device Tree to 03ff7000, end 03fff54d ... OK
70

    
71
Starting kernel ...
72

    
73
Booting Linux on physical CPU 0x0
74
Initializing cgroup subsys cpuset
75
Linux version 3.16.0-00291-gc24173f (dvincelette@eva) (gcc version 4.8.3 20140401 (prerelease) (crosstool-NG linaro-1.13.1-4.8-2014.04 - Linaro GCC 4.8-2014.04) ) #9 SMP Tue May 17 15:37:08 EDT 2016
76
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
77
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
78
Machine model: MitySOM-5CSX Altera SOCFPGA Cyclone V
79
Memory policy: Data cache writealloc
80
PERCPU: Embedded 8 pages/cpu @bf7d0000 s11008 r8192 d13568 u32768
81
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 260096
82
Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait
83
PID hash table entries: 4096 (order: 2, 16384 bytes)
84
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
85
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
86
Memory: 1031400K/1048576K available (5570K kernel code, 282K rwdata, 1564K rodata, 394K init, 143K bss, 17176K reserved, 0K highmem)
87
Virtual kernel memory layout:
88
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
89
    fixmap  : 0xffc00000 - 0xffe00000   (2048 kB)
90
    vmalloc : 0xc0800000 - 0xff000000   (1000 MB)
91
    lowmem  : 0x80000000 - 0xc0000000   (1024 MB)
92
    pkmap   : 0x7fe00000 - 0x80000000   (   2 MB)
93
    modules : 0x7f000000 - 0x7fe00000   (  14 MB)
94
      .text : 0x80008000 - 0x806ffbec   (7135 kB)
95
      .init : 0x80700000 - 0x80762b00   ( 395 kB)
96
      .data : 0x80764000 - 0x807aaa08   ( 283 kB)
97
       .bss : 0x807aaa08 - 0x807ce91c   ( 144 kB)
98
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
99
Hierarchical RCU implementation.
100
NR_IRQS:16 nr_irqs:16 16
101
L2C: platform modifies aux control register: 0x02060000 -> 0x32460000
102
L2C: platform provided aux values permit register corruption.
103
L2C: DT/platform modifies aux control register: 0x02060000 -> 0x32460000
104
L2C-310 erratum 769419 enabled
105
L2C-310 enabling early BRESP for Cortex-A9
106
L2C-310 full line of zeros enabled for Cortex-A9
107
L2C-310 ID prefetch enabled, offset 1 lines
108
L2C-310 dynamic clock gating enabled, standby mode enabled
109
L2C-310 cache controller enabled, 8 ways, 512 kB
110
L2C-310: CACHE_ID 0x410030c9, AUX_CTRL 0x76460001
111
sched_clock: 32 bits at 100MHz, resolution 10ns, wraps every 42949672950ns
112
Console: colour dummy device 80x30
113
Calibrating delay loop... 1594.16 BogoMIPS (lpj=7970816)
114
pid_max: default: 32768 minimum: 301
115
Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
116
Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
117
CPU: Testing write buffer coherency: ok
118
ftrace: allocating 19015 entries in 56 pages
119
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
120
Setting up static identity map for 0x506c18 - 0x506c70
121
CPU1: Booted secondary processor
122
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
123
Brought up 2 CPUs
124
SMP: Total of 2 processors activated.
125
CPU: All CPU(s) started in SVC mode.
126
devtmpfs: initialized
127
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
128
NET: Registered protocol family 16
129
fpga bridge driver
130
DMA: preallocated 256 KiB pool for atomic coherent allocations
131
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
132
hw-breakpoint: maximum watchpoint size is 4 bytes.
133
altera_hps2fpga_bridge soc:fpgabridge@0: fpga bridge [hps2fpga] registered as device hps2fpga
134
altera_hps2fpga_bridge soc:fpgabridge@0: init-val not specified
135
altera_hps2fpga_bridge soc:fpgabridge@1: fpga bridge [lshps2fpga] registered as device lwhps2fpga
136
altera_hps2fpga_bridge soc:fpgabridge@1: init-val not specified
137
altera_hps2fpga_bridge soc:fpgabridge@2: fpga bridge [fpga2hps] registered as device fpga2hps
138
altera_hps2fpga_bridge soc:fpgabridge@2: init-val not specified
139
FPGA Mangager framework driver
140
vgaarb: loaded
141
SCSI subsystem initialized
142
usbcore: registered new interface driver usbfs
143
usbcore: registered new interface driver hub
144
usbcore: registered new device driver usb
145
pps_core: LinuxPPS API ver. 1 registered
146
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
147
PTP clock support registered
148
Switched to clocksource timer1
149
NET: Registered protocol family 2
150
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
151
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
152
TCP: Hash tables configured (established 8192 bind 8192)
153
TCP: reno registered
154
UDP hash table entries: 512 (order: 2, 16384 bytes)
155
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
156
NET: Registered protocol family 1
157
RPC: Registered named UNIX socket transport module.
158
RPC: Registered udp transport module.
159
RPC: Registered tcp transport module.
160
RPC: Registered tcp NFSv4.1 backchannel transport module.
161
hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
162
arm-pmu arm-pmu: PMU:CTI successfully enabled for 2 cores
163
futex hash table entries: 512 (order: 3, 32768 bytes)
164
NFS: Registering the id_resolver key type
165
Key type id_resolver registered
166
Key type id_legacy registered
167
ntfs: driver 2.1.30 [Flags: R/W].
168
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
169
msgmni has been set to 2014
170
io scheduler noop registered (default)
171
altvipfb ff200100.hdmi0x0100: fb0: altvipfb frame buffer device at 0x3e800000+0x384000
172
dma-pl330 ffe01000.pdma: Loaded driver for PL330 DMAC-3412784
173
dma-pl330 ffe01000.pdma: 	DBUFF-512x8bytes Num_Chans-8 Num_Peri-32 Num_Events-8
174
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
175
console [ttyS0] disabled
176
ffc02000.serial0: ttyS0 at MMIO 0xffc02000 (irq = 194, base_baud = 6250000) is a 16550A
177
console [ttyS0] enabled
178
ffc03000.serial1: ttyS1 at MMIO 0xffc03000 (irq = 195, base_baud = 6250000) is a 16550A
179
altera_fpga_manager ff706000.fpgamgr: fpga manager [Altera FPGA Manager] registered as minor 0
180
brd: module loaded
181
at24 0-0050: 2048 byte 24c16 EEPROM, writable, 1 bytes/write
182
cadence-qspi ff705000.spi: DMA NOT enabled
183
cadence-qspi ff705000.spi: master is unqueued, this is deprecated
184
m25p80 spi2.0: n25q128a11 (16384 Kbytes)
185
6 ofpart partitions found on MTD device spi2.0
186
Creating 6 MTD partitions on "spi2.0":
187
0x000000000000-0x000000040000 : "Preloader Image 0-3"
188
0x000000040000-0x000000050000 : "U-Boot Env"
189
0x000000050000-0x000000060000 : "DTB"
190
0x000000060000-0x0000000e0000 : "U-Boot"
191
0x0000000e0000-0x0000008e0000 : "Kernel"
192
0x0000008e0000-0x000001000000 : "FPGA"
193
m25p80 spi2.1: n25q128a11 (16384 Kbytes)
194
1 ofpart partitions found on MTD device spi2.1
195
Creating 1 MTD partitions on "spi2.1":
196
0x000000000000-0x000001000000 : "Data"
197
cadence-qspi ff705000.spi: Cadence QSPI controller driver
198
CAN device driver interface
199
c_can_platform ffc00000.can: c_can_platform device registered (regs=c0c6e000, irq=163)
200
c_can_platform ffc01000.can: c_can_platform device registered (regs=c0c70000, irq=167)
201
/soc/ethernet@ff702000: could not get #reset-cells for /soc/rstmgr@ffd05000
202
stmmaceth ff702000.ethernet: no reset control found
203
stmmac - user ID: 0x10, Synopsys ID: 0x37
204
 Ring mode enabled
205
 DMA HW capability register supported
206
 Enhanced/Alternate descriptors
207
	Enabled extended descriptors
208
 RX Checksum Offload Engine supported (type 2)
209
 TX Checksum insertion supported
210
 Enable RX Mitigation via HW Watchdog Timer
211
stmmac-mdio ff702000.mdio: mdio@ff702000
212
libphy: stmmac_mdio: probed
213
dwc2 ffb40000.usb: EPs: 15, dedicated fifos, 8064 entries in SPRAM
214
dwc2 ffb40000.usb: DWC OTG Controller
215
dwc2 ffb40000.usb: new USB bus registered, assigned bus number 1
216
dwc2 ffb40000.usb: irq 160, io mem 0x00000000
217
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
218
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
219
usb usb1: Product: DWC OTG Controller
220
usb usb1: Manufacturer: Linux 3.16.0-00291-gc24173f dwc2_hsotg
221
usb usb1: SerialNumber: ffb40000.usb
222
hub 1-0:1.0: USB hub found
223
hub 1-0:1.0: 1 port detected
224
usbcore: registered new interface driver usb-storage
225
mousedev: PS/2 mouse device common for all mice
226
rtc-ab18xx 0-0069: rtc core: registered ab1803 as rtc0
227
rtc-ab18xx 0-0069: 192 bytes nvram
228
i2c /dev entries driver
229
lm73 0-004c: sensor 'lm73'
230
Synopsys Designware Multimedia Card Interface Driver
231
dw_mmc ff704000.dwmmc0: no vmmc regulator found: -19
232
dw_mmc ff704000.dwmmc0: Using internal DMA controller.
233
dw_mmc ff704000.dwmmc0: Version ID is 240a
234
dw_mmc ff704000.dwmmc0: DW MMC controller at irq 171, 32 bit host data width, 1024 deep fifo
235
dw_mmc ff704000.dwmmc0: 1 slots initialized
236
lp5562 0-0030: internal clock used
237
ledtrig-cpu: registered to indicate activity on CPUs
238
usbcore: registered new interface driver usbhid
239
usbhid: USB HID core driver
240
oprofile: using arm/armv7-ca9
241
TCP: cubic registered
242
NET: Registered protocol family 17
243
NET: Registered protocol family 15
244
can: controller area network core (rev 20120528 abi 9)
245
NET: Registered protocol family 29
246
can: raw protocol (rev 20120528)
247
can: broadcast manager protocol (rev 20120528 t)
248
can: netlink gateway (rev 20130117) max_hops=1
249
8021q: 802.1Q VLAN Support v1.8
250
Key type dns_resolver registered
251
ThumbEE CPU extension supported.
252
Registering SWP/SWPB emulation handler
253
input: soc:gpio_keys as /devices/soc/soc:gpio_keys/input/input0
254
Waiting for root device /dev/mmcblk0p2...
255
mmc_host mmc0: Bus speed (slot 0) = 200000000Hz (slot req 50000000Hz, actual 50000000HZ div = 2)
256
mmc0: new high speed SDHC card at address 0007
257
mmcblk0: mmc0:0007 SL16G 14.4 GiB 
258
 mmcblk0: p1 p2 p3
259
kjournald starting.  Commit interval 5 seconds
260
EXT3-fs (mmcblk0p2): using internal journal
261
EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
262
VFS: Mounted root (ext3 filesystem) on device 179:2.
263
devtmpfs: mounted
264
Freeing unused kernel memory: 392K (80700000 - 80762000)
265

    
266
INIT: version 2.88 booting
267

    
268
Setting up HDMI Transmitter
269
Writing Config
270
Done Writing Config
271
Starting udev
272
udevd[88]: starting version 182
273
random: nonblocking pool is initialized
274

    
275
udevadm settle - timeout of 3 seconds reached, the event queue contains:
276
  /sys/devices/soc/ff704000.dwmmc0/mmc_host/mmc0/mmc0:0007/block/mmcblk0 (659)
277
  /sys/devices/soc/ff704000.dwmmc0/mmc_host/mmc0/mmc0:0007/block/mmcblk0/mmcblk0p1 (660)
278
  /sys/devices/soc/ff704000.dwmmc0/mmc_host/mmc0/mmc0:0007/block/mmcblk0/mmcblk0p2 (661)
279
  /sys/devices/soc/ff704000.dwmmc0/mmc_host/mmc0/mmc0:0007/block/mmcblk0/mmcblk0p3 (662)
280
Starting Bootlog daemon: bootlogd.
281

    
282
Configuring network interfaces... udhcpc (v1.21.1) started
283

    
284
run-parts: /etc/udhcpc.d/00avahi-autoipd exited with code 1
285

    
286
Sending discover...
287

    
288
stmmaceth ff702000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
289
Sending discover...
290

    
291
Sending select for 10.21.200.77...
292

    
293
Lease of 10.21.200.77 obtained, lease time 691200
294

    
295
run-parts: /etc/udhcpc.d/00avahi-autoipd exited with code 1
296

    
297
/etc/udhcpc.d/50default: Adding DNS 10.22.203.252
298

    
299
/etc/udhcpc.d/50default: Adding DNS 10.22.203.253
300

    
301
done.
302

    
303
Starting rpcbind daemon...rpcbind: cannot create socket for udp6
304

    
305

    
306
rpcbind: cannot create socket for tcp6
307

    
308

    
309
done.
310

    
311
net.ipv4.conf.default.rp_filter = 1
312

    
313
net.ipv4.conf.all.rp_filter = 1
314

    
315
Starting atd: OK
316

    
317

    
318
INIT: Entering runlevel: 5
319

    
320

    
321
Starting system message bus: dbus.
322

    
323
Starting OpenBSD Secure Shell server: sshd
324

    
325
done.
326

    
327
creating NFS state directory: done
328

    
329
NFS daemon support not enabled in kernel
330

    
331
Starting system log daemon...0
332

    
333
Starting kernel log daemon...0
334

    
335
 * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
336

    
337
[ ok ]
338

    
339
 * Starting Avahi Unicast DNS Configuration Daemon: avahi-dnsconfd
340

    
341
[ ok ]
342

    
343
Starting Lighttpd Web Server: lighttpd.
344

    
345
Starting crond: OK
346

    
347
Starting Network Interface Plugging Daemon: eth0.
348

    
349
Stopping Bootlog daemon: bootlogd.
350

    
351

    
352
Poky (Yocto Project Reference Distro) 1.5.4 mitysom-5csx /dev/ttyS0
353

    
354

    
355

    
356
mitysom-5csx login: root
357
root@mitysom-5csx:~# ifconfig
358
eth0      Link encap:Ethernet  HWaddr 70:b3:d5:b5:1f:e9  
359
          inet addr:10.21.200.77  Bcast:0.0.0.0  Mask:255.255.255.0
360
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
361
          RX packets:81 errors:0 dropped:0 overruns:0 frame:0
362
          TX packets:23 errors:0 dropped:0 overruns:0 carrier:0
363
          collisions:0 txqueuelen:1000 
364
          RX bytes:9381 (9.1 KiB)  TX bytes:4257 (4.1 KiB)
365
          Interrupt:152 Base address:0x4000 
366

    
367
lo        Link encap:Local Loopback  
368
          inet addr:127.0.0.1  Mask:255.0.0.0
369
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
370
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
371
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
372
          collisions:0 txqueuelen:0 
373
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
374

    
375
root@mitysom-5csx:~# 
(1-1/2) Go to top
Add picture from clipboard (Maximum size: 1 GB)