Project

General

Profile

RE: NFS configuration ยป Boot Sequence with nfsrootdebug.txt

Leonid Volpert, 07/12/2013 01:37 PM

 
1
U-Boot# run net_boot
2
failed to read bmcr on phy id 0
3
Vitesse VSC8601 PHY detected at addr 1
4
Auto negotiation took 3360 ms
5
link up on port 1, speed 1000, full duplex
6
Using cpsw device
7
TFTP from server 10.0.0.1; our IP address is 10.0.0.22
8
Filename 'uImage-3.1.0-00046-g5a51b9c-CL'.
9
Load address: 0x80007fc0
10
Loading: #################################################################
11
         #################################################################
12
         #################################################################
13
         #################################################################
14
         #################################################################
15
         #################################################################
16
         #################################################################
17
         #################################################################
18
         #################################################################
19
         ########################
20
done
21
Bytes transferred = 3115864 (2f8b58 hex)
22
## Booting kernel from Legacy Image at 80007fc0 ...
23
   Image Name:   Linux-3.1.0-00046-g5a51b9c-dirty
24
   Image Type:   ARM Linux Kernel Image (uncompressed)
25
   Data Size:    3115800 Bytes = 3 MiB
26
   Load Address: 80008000
27
   Entry Point:  80008000
28
   Verifying Checksum ... OK
29
   XIP Kernel Image ... OK
30
OK
31

    
32
Starting kernel ...
33

    
34
Uncompressing Linux... done, booting the kernel.
35
[    0.000000] Linux version 3.1.0-00046-g5a51b9c-dirty (iskander@mitydsp) (gcc version 4.5.3 20110311 (prerelease) (GCC) ) #24 We
36
d Mar 7 14:23:34 EST 2012
37
[    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7f
38
[    0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
39
[    0.000000] Machine: mityarm335x
40
[    0.000000] Memory policy: ECC disabled, Data cache writeback
41
[    0.000000] AM335X ES1.0 (neon )
42
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
43
[    0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/nfs nfsroot=10.0.0.1:/home/likewise-open/SCHICK_NT/lvolpert/D
44
ev/3D/MityARM-rootfs_dev,nolock nfsrootdebug rw ip=10.0.0.22:10.0.0.1:10.0.0.1:255.255.255.0:devubuntu01:eth0:off
45
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
46
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
47
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
48
[    0.000000] Memory: 256MB = 256MB total
49
[    0.000000] Memory: 252724k/252724k available, 9420k reserved, 0K highmem
50
[    0.000000] Virtual kernel memory layout:
51
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
52
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
53
[    0.000000]     DMA     : 0xffa00000 - 0xffe00000   (   4 MB)
54
[    0.000000]     vmalloc : 0xd0800000 - 0xf8000000   ( 632 MB)
55
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
56
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
57
[    0.000000]       .text : 0xc0008000 - 0xc060f000   (6172 kB)
58
[    0.000000]       .init : 0xc060f000 - 0xc064a000   ( 236 kB)
59
[    0.000000]       .data : 0xc064a000 - 0xc06bd038   ( 461 kB)
60
[    0.000000]        .bss : 0xc06bd05c - 0xc06f7a20   ( 235 kB)
61
[    0.000000] NR_IRQS:396
62
[    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts
63
[    0.000000] Total of 128 interrupts on 1 active controller
64
[    0.000000] OMAP clockevent source: GPTIMER1 at 24000000 Hz
65
[    0.000000] OMAP clocksource: GPTIMER2 at 24000000 Hz
66
[    0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
67
[    0.000000] Console: colour dummy device 80x30
68
[    0.000197] Calibrating delay loop... 718.02 BogoMIPS (lpj=3590144)
69
[    0.059022] pid_max: default: 32768 minimum: 301
70
[    0.059149] Security Framework initialized
71
[    0.059248] Mount-cache hash table entries: 512
72
[    0.059617] CPU: Testing write buffer coherency: ok
73
[    0.064177] print_constraints: dummy: 
74
[    0.064557] NET: Registered protocol family 16
75
[    0.064893] GPMC revision 6.0
76
[    0.066883] OMAP GPIO hardware version 0.1
77
[    0.069008] omap_l3_smx omap_l3_smx.0: couldn't find resource
78
[    0.069752] omap_mux_init: Add partition: #1: core, flags: 0
79
[    0.072551]  omap_i2c.3: alias fck already exists
80
[    0.072827]  omap_i2c.2: alias fck already exists
81
[    0.074392] Registering mcspi 1 [2]
82
[    0.074435]  omap2_mcspi.1: alias fck already exists
83
[    0.074629] Registering mcspi 2 [2]
84
[    0.074663]  omap2_mcspi.2: alias fck already exists
85
[    0.078123] baseboard_init [MityARM-335x DevKit]...
86
[    0.078425]  omap_hsmmc.0: alias fck already exists
87
[    0.080455] Configuring audio...
88
[    0.080525] _omap_mux_get_by_name: Could not find signal mii1_refclk.mcasp1_ahclkx
89
[    0.080569] Registering mcasp1
90
[    0.080819]  omap_i2c.1: alias fck already exists
91
[    0.100332] bio: create slab <bio-0> at 0
92
[    0.102299] SCSI subsystem initialized
93
[    0.104421] usbcore: registered new interface driver usbfs
94
[    0.104751] usbcore: registered new interface driver hub
95
[    0.104965] usbcore: registered new device driver usb
96
[    0.119183] omap_i2c omap_i2c.3: bus 3 rev4.0 at 100 kHz
97
[    0.120319] tps65910 3-002d: JTAGREVNUM 0x0
98
[    0.121959] print_constraints: VRTC: 
99
[    0.122641] print_constraints: VIO: at 1800 mV 
100
[    0.124905] print_constraints: VDD1: 600 <--> 1500 mV at 1262 mV normal 
101
[    0.126430] print_constraints: VDD2: at 1137 mV 
102
[    0.126670] print_constraints: VDD3: 5000 mV 
103
[    0.127309] print_constraints: VDIG1: at 1800 mV 
104
[    0.127970] print_constraints: VDIG2: at 1800 mV 
105
[    0.128633] print_constraints: VPLL: at 1800 mV 
106
[    0.129381] print_constraints: VDAC: at 1800 mV 
107
[    0.130060] print_constraints: VAUX1: at 1800 mV 
108
[    0.130716] print_constraints: VAUX2: at 3300 mV 
109
[    0.131382] print_constraints: VAUX33: at 3300 mV 
110
[    0.132047] print_constraints: VMMC: at 3300 mV 
111
[    0.132508] tps65910 3-002d: No interrupt support, no core IRQ
112
[    0.149102] omap_i2c omap_i2c.2: bus 2 rev4.0 at 100 kHz
113
[    0.169084] omap_i2c omap_i2c.1: bus 1 rev4.0 at 100 kHz
114
[    0.170140] Advanced Linux Sound Architecture Driver Version 1.0.24.
115
[    0.171204] Switching to clocksource gp timer
116
[    0.179103] Switched to NOHz mode on CPU #0
117
[    0.186421] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
118
[    0.186622] musb-hdrc musb-hdrc.0: dma type: pio
119
[    0.187476] musb-hdrc musb-hdrc.0: USB OTG mode controller at d080a000 using PIO, IRQ 18
120
[    0.187653] musb-hdrc musb-hdrc.1: dma type: pio
121
[    0.188380] musb-hdrc musb-hdrc.1: USB OTG mode controller at d080c800 using PIO, IRQ 19
122
[    0.188784] NET: Registered protocol family 2
123
[    0.188973] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
124
[    0.189255] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
125
[    0.189413] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
126
[    0.189510] TCP: Hash tables configured (established 8192 bind 8192)
127
[    0.189523] TCP reno registered
128
[    0.189536] UDP hash table entries: 256 (order: 0, 4096 bytes)
129
[    0.189560] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
130
[    0.189745] NET: Registered protocol family 1
131
[    0.190030] RPC: Registered named UNIX socket transport module.
132
[    0.190044] RPC: Registered udp transport module.
133
[    0.190054] RPC: Registered tcp transport module.
134
[    0.190063] RPC: Registered tcp NFSv4.1 backchannel transport module.
135
[    0.190272] NetWinder Floating Point Emulator V0.97 (double precision)
136
[    0.202953] VFS: Disk quotas dquot_6.5.2
137
[    0.203019] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
138
[    0.203580] msgmni has been set to 493
139
[    0.204318] io scheduler noop registered
140
[    0.204333] io scheduler deadline registered
141
[    0.204397] io scheduler cfq registered (default)
142
[    0.205531] da8xx_lcdc da8xx_lcdc.0: GLCD: Found svga_800x600 panel
143
[    0.205562] DA8XX FB - no options passed
144
[    0.205571] DA8XX FB - BPP = 16
145
[    0.205581] DA8XX FB - BPP = 16 [16 -> 32]
146
[    0.205592] DA8XX FB: 800 x 600 16 bpp
147
[    0.214439] Console: switching to colour frame buffer device 100x37
148
[    0.219345] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
149
[    0.221081] omap_uart.0: ttyO0 at MMIO 0x44e09000 (irq = 72) is a OMAP UART0
150
[    0.853685] console [ttyO0] enabled
151
[    0.857885] omap_uart.1: ttyO1 at MMIO 0x48022000 (irq = 73) is a OMAP UART1
152
[    0.865661] omap_uart.2: ttyO2 at MMIO 0x48024000 (irq = 74) is a OMAP UART2
153
[    0.873368] omap_uart.3: ttyO3 at MMIO 0x481a6000 (irq = 44) is a OMAP UART3
154
[    0.881019] omap_uart.4: ttyO4 at MMIO 0x481a8000 (irq = 45) is a OMAP UART4
155
[    0.888729] omap_uart.5: ttyO5 at MMIO 0x481aa000 (irq = 46) is a OMAP UART5
156
[    0.905053] brd: module loaded
157
[    0.913028] loop: module loaded
158
[    0.916481] i2c-core: driver [tsl2550] using legacy suspend method
159
[    0.922969] i2c-core: driver [tsl2550] using legacy resume method
160
[    0.929389] at24 2-0050: 256 byte 24c02 EEPROM, read-only, 0 bytes/write
161
[    0.942249] MityARM-335x: Found MAC = 00:00:00:00:00:00
162
[    0.947699] MityARM-335x: Part Number = 3359-GX-226-RL
163
[    0.955778] m25p80 spi2.0: m25p64-nonjedec (8192 Kbytes)
164
[    0.961391] Creating 1 MTD partitions on "spi_flash":
165
[    0.966665] 0x000000000000-0x000000800000 : "NOR User Defined"
166
[    0.974414] omap2-nand driver initializing
167
[    0.979043] ONFI flash detected
168
[    0.982486] ONFI param page 0 valid
169
[    0.986129] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08ABAEAWP)
170
[    0.994498] Creating 8 MTD partitions on "omap2-nand.0":
171
[    1.000039] 0x000000000000-0x000000020000 : "SPL"
172
[    1.006401] 0x000000020000-0x000000040000 : "SPL.backup1"
173
[    1.013383] 0x000000040000-0x000000060000 : "SPL.backup2"
174
[    1.020244] 0x000000060000-0x000000080000 : "SPL.backup3"
175
[    1.027182] 0x000000080000-0x000000260000 : "U-Boot"
176
[    1.034341] 0x000000260000-0x000000280000 : "U-Boot Env"
177
[    1.041108] 0x000000280000-0x000000780000 : "Kernel"
178
[    1.049835] 0x000000780000-0x000010000000 : "File System"
179
[    1.159097] OneNAND driver initializing
180
[    1.211263] davinci_mdio davinci_mdio.0: davinci mdio revision 1.6
181
[    1.217719] davinci_mdio davinci_mdio.0: detected phy mask fffffffd
182
[    1.224913] davinci_mdio.0: probed
183
[    1.228463] davinci_mdio davinci_mdio.0: phy[1]: device 0:01, driver unknown
184
[    1.235997] CAN device driver interface
185
[    1.239992] CAN bus driver for Bosch D_CAN controller 1.0
186
[    1.246419] d_can d_can.0: d_can device registered (irq=52, irq_obj=53)
187
[    1.254066] d_can d_can.1: d_can device registered (irq=55, irq_obj=56)
188
[    1.261812] usbcore: registered new interface driver cdc_ether
189
[    1.268042] usbcore: registered new interface driver cdc_subset
190
[    1.274290] Initializing USB Mass Storage driver...
191
[    1.279600] usbcore: registered new interface driver usb-storage
192
[    1.285886] USB Mass Storage support registered.
193
[    1.290764]  gadget: using random self ethernet address
194
[    1.296231]  gadget: using random host ethernet address
195
[    1.302207] usb0: MAC 42:3c:44:bf:5a:f6
196
[    1.306213] usb0: HOST MAC da:f7:3c:aa:0e:4e
197
[    1.310731]  gadget: Ethernet Gadget, version: Memorial Day 2008
198
[    1.317031]  gadget: g_ether ready
199
[    1.320603] musb-hdrc musb-hdrc.0: MUSB HDRC host driver
200
[    1.326245] musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus number 1
201
[    1.334084] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
202
[    1.341165] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
203
[    1.348709] usb usb1: Product: MUSB HDRC host driver
204
[    1.353891] usb usb1: Manufacturer: Linux 3.1.0-00046-g5a51b9c-dirty musb-hcd
205
[    1.361337] usb usb1: SerialNumber: musb-hdrc.0
206
[    1.366923] hub 1-0:1.0: USB hub found
207
[    1.370851] hub 1-0:1.0: 1 port detected
208
[    1.375661] musb-hdrc musb-hdrc.1: MUSB HDRC host driver
209
[    1.381219] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 2
210
[    1.389044] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
211
[    1.396136] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
212
[    1.403672] usb usb2: Product: MUSB HDRC host driver
213
[    1.408846] usb usb2: Manufacturer: Linux 3.1.0-00046-g5a51b9c-dirty musb-hcd
214
[    1.416290] usb usb2: SerialNumber: musb-hdrc.1
215
[    1.421718] hub 2-0:1.0: USB hub found
216
[    1.425649] hub 2-0:1.0: 1 port detected
217
[    1.430714] mousedev: PS/2 mouse device common for all mice
218
[    1.437751] omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0
219
[    1.444453] omap_rtc: already running
220
[    1.448493] i2c /dev entries driver
221
[    1.504269] OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
222
[    1.511392] cpuidle: using governor ladder
223
[    1.516120] cpuidle: using governor menu
224
[    1.523866] usbcore: registered new interface driver usbhid
225
[    1.529697] usbhid: USB HID core driver
226
[    1.534516] usbcore: registered new interface driver snd-usb-audio
227
[    1.557196] tlv320aic26-codec spi1.1: Probing AIC26 SoC CODEC driver
228
[    1.582753] asoc: tlv320aic26-hifi <-> davinci-mcasp.1 mapping ok
229
[    1.590321] ALSA device list:
230
[    1.593468]   #0: MityARM-335X DevKit
231
[    1.597287] oprofile: hardware counters not available
232
[    1.602559] oprofile: using timer interrupt.
233
[    1.607032] nf_conntrack version 0.5.0 (3948 buckets, 15792 max)
234
[    1.613813] ip_tables: (C) 2000-2006 Netfilter Core Team
235
[    1.619472] TCP cubic registered
236
[    1.622869] NET: Registered protocol family 17
237
[    1.627508] can: controller area network core (rev 20090105 abi 8)
238
[    1.634052] NET: Registered protocol family 29
239
[    1.638728] can: raw protocol (rev 20090105)
240
[    1.643191] can: broadcast manager protocol (rev 20090105 t)
241
[    1.649129] Registering the dns_resolver key type
242
[    1.654133] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
243
[    1.662141] ThumbEE CPU extension supported.
244
[    1.670769] regulator_init_complete: VMMC: incomplete constraints, leaving on
245
[    1.678732] regulator_init_complete: VAUX33: incomplete constraints, leaving on
246
[    1.686837] regulator_init_complete: VAUX2: incomplete constraints, leaving on
247
[    1.694855] regulator_init_complete: VAUX1: incomplete constraints, leaving on
248
[    1.702852] regulator_init_complete: VDAC: incomplete constraints, leaving on
249
[    1.710740] regulator_init_complete: VPLL: incomplete constraints, leaving on
250
[    1.718652] regulator_init_complete: VDIG2: incomplete constraints, leaving on
251
[    1.726654] regulator_init_complete: VDIG1: incomplete constraints, leaving on
252
[    1.735117] regulator_init_complete: VDD2: incomplete constraints, leaving on
253
[    1.743034] regulator_init_complete: VIO: incomplete constraints, leaving on
254
[    1.750868] regulator_init_complete: VRTC: incomplete constraints, leaving on
255
[    1.758620] Detected MACID=bc:6a:29:87:7e:b
256
[    1.764633] omap_rtc omap_rtc: setting system clock to 2011-12-25 08:54:45 UTC (1324803285)
257
[    1.775971] PHY 0:00 not found
258
[    1.779413] 
259
[    1.779417] CPSW phy found : id is : 0x70421
260
[    1.788384] mmc0: new SD card at address aaaa
261
[    1.793620] mmcblk0: mmc0:aaaa SU02G 1.84 GiB 
262
[    1.800537]  mmcblk0: p1 p2 p3
263
[    3.772190] PHY: 0:01 - Link is Up - 1000/Full
264
[    3.801751] IP-Config: Complete:
265
[    3.805118]      device=eth0, addr=10.0.0.22, mask=255.255.255.0, gw=10.0.0.1,
266
[    3.812427]      host=devubuntu01, domain=, nis-domain=(none),
267
[    3.818510]      bootserver=10.0.0.1, rootserver=10.0.0.1, rootpath=
268
[    3.825842] Root-NFS: nfsroot=/home/likewise-open/SCHICK_NT/lvolpert/Dev/3D/MityARM-rootfs_dev,nolock
269
[    3.835629] NFS: nfs mount opts='vers=2,udp,rsize=4096,wsize=4096,nolock,nolock,addr=10.0.0.1'
270
[    3.844633] NFS:   parsing nfs mount option 'vers=2'
271
[    3.849823] NFS:   parsing nfs mount option 'udp'
272
[    3.854744] NFS:   parsing nfs mount option 'rsize=4096'
273
[    3.860285] NFS:   parsing nfs mount option 'wsize=4096'
274
[    3.865836] NFS:   parsing nfs mount option 'nolock'
275
[    3.871010] NFS:   parsing nfs mount option 'nolock'
276
[    3.876192] NFS:   parsing nfs mount option 'addr=10.0.0.1'
277
[    3.882026] NFS: MNTPATH: '/home/likewise-open/SCHICK_NT/lvolpert/Dev/3D/MityARM-rootfs_dev'
278
[    3.890826] NFS: sending MNT request for 10.0.0.1:/home/likewise-open/SCHICK_NT/lvolpert/Dev/3D/MityARM-rootfs_dev
279
[    3.912964] NFS: MNT server returned result -13
280
[    3.917696] NFS: unable to mount server 10.0.0.1, error -13
281
[    3.923558] VFS: Unable to mount root fs via NFS, trying floppy.
282
[    3.930300] VFS: Cannot open root device "nfs" or unknown-block(2,0)
283
[    3.936962] Please append a correct "root=" boot option; here are the available partitions:
284
[    3.945721] 1f00            8192 mtdblock0  (driver?)
285
[    3.950992] 1f01             128 mtdblock1  (driver?)
286
[    3.956276] 1f02             128 mtdblock2  (driver?)
287
[    3.961555] 1f03             128 mtdblock3  (driver?)
288
[    3.966825] 1f04             128 mtdblock4  (driver?)
289
[    3.972105] 1f05            1920 mtdblock5  (driver?)
290
[    3.977375] 1f06             128 mtdblock6  (driver?)
291
[    3.982654] 1f07            5120 mtdblock7  (driver?)
292
[    3.987923] 1f08          254464 mtdblock8  (driver?)
293
[    3.993204] b300         1931264 mmcblk0  driver: mmcblk
294
[    3.998753]   b301           72261 mmcblk0p1 00000000-0000-0000-0000-000000000mmcblk0p1
295
[    4.007119]   b302          923737 mmcblk0p2 00000000-0000-0000-0000-000000000mmcblk0p2
296
[    4.015479]   b303          915705 mmcblk0p3 00000000-0000-0000-0000-000000000mmcblk0p3
297
[    4.023837] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0)
298
[    4.032457] Backtrace: 
299
[    4.035033] [<c0017990>] (dump_backtrace+0x0/0x110) from [<c0412618>] (dump_stack+0x18/0x1c)
300
[    4.043846]  r6:cf9a2000 r5:c063b84c r4:c06be120 r3:c066aad0
301
[    4.049766] [<c0412600>] (dump_stack+0x0/0x1c) from [<c0412688>] (panic+0x6c/0x1a0)
302
[    4.057783] [<c041261c>] (panic+0x0/0x1a0) from [<c060fcb4>] (mount_block_root+0x184/0x228)
303
[    4.066496]  r3:c066aad0 r2:00000000 r1:cf81bf58 r0:c0579da0
304
[    4.072417]  r7:00008000
305
[    4.075067] [<c060fb30>] (mount_block_root+0x0/0x228) from [<c060ff1c>] (mount_root+0xd8/0xe0)
306
[    4.084060] [<c060fe44>] (mount_root+0x0/0xe0) from [<c06100c4>] (prepare_namespace+0x1a0/0x1dc)
307
[    4.093225]  r4:c06bd0e0
308
[    4.095874] [<c060ff24>] (prepare_namespace+0x0/0x1dc) from [<c060f90c>] (kernel_init+0x124/0x130)
309
[    4.105218]  r5:c0649bbc r4:c0649bbc
310
[    4.108970] [<c060f7e8>] (kernel_init+0x0/0x130) from [<c0040904>] (do_exit+0x0/0x6a0)
311
[    4.117230]  r5:c060f7e8 r4:00000000
312

    
    (1-1/1)
    Go to top
    Add picture from clipboard (Maximum size: 1 GB)