Project

General

Profile

RE: AM62A eMMC Boot - Kernel Device Tree » emmc boot.txt

Ben H, 02/25/2026 03:20 PM

 
1
U-Boot SPL 2025.01-g847ec74f66f8 (Jan 07 2026 - 20:17:44 +0000)
2
SYSFW ABI: 4.0 (firmware rev 0x000b '11.1.5--v11.01.05 (Fancy Rat)')
3
DM ABI: 3.0 (firmware ver 0x000b 'MSDK.11.01.00.16-dirty--v11.01.02' patch_ver: 2)
4
Trying to boot from MMC1
5
Authentication passed
6
Authentication passed
7

    
8

    
9
U-Boot 2025.01-g847ec74f66f8 (Jan 07 2026 - 20:17:44 +0000)
10

    
11
SoC:   AM62AX SR1.0 HS-FS
12
Model: Critical Link MitySOM-AM62A
13
MitySOM-62x - Model No: 62A74-TX-XAE-RI Serial No: 24008072 Part Number: 80-001736RI-2A
14
DRAM:  4 GiB
15
Core:  112 devices, 31 uclasses, devicetree: separate
16
MMC:   mmc@fa10000: 0, mmc@fa00000: 1
17
Loading Environment from FAT... MMC: no card present
18
** Bad device specification mmc 1 **
19
Loading Environment from MMC... Reading from MMC(0)... OK
20
In:    serial@2800000
21
Out:   serial@2800000
22
Err:   serial@2800000
23
Net:   eth0: ethernet@8000000port@1, eth1: ethernet@8000000port@2
24
Hit any key to stop autoboot:  0 
25
=> env default -a
26
## Resetting to default environment
27
=> saveenv
28
Saving Environment to MMC... Writing to MMC(0)... OK
29
=> setenv xtrace yes
30
=> setenv fdtfile "ti/k3-am62a7-mitysom-tfc.dtb"    
31
+ setenv fdtfile ti/k3-am62a7-mitysom-tfc.dtb
32
=> mmc partconf 0 1 1 1
33
+ mmc partconf 0 1 1 1
34
=> mmc bootbus 0 2 0 0
35
+ mmc bootbus 0 2 0 0
36
Set to BOOT_BUS_WIDTH = 0x2, RESET = 0x0, BOOT_MODE = 0x0
37
=> setenv mmcdev 0
38
+ setenv mmcdev 0
39
=> setenv bootpart 0
40
+ setenv bootpart 0
41
=> saveenv
42
+ saveenv
43
Saving Environment to MMC... Writing to MMC(0)... OK
44
=> boot
45
+ boot
46
+ run reset_hdmi
47
+ echo Resetting HDMI tfp410
48
Resetting HDMI tfp410
49
+ i2c dev 1
50
Setting bus to 1
51
+ i2c mw 0x20 3 fb
52
+ i2c mw 0x20 1 fb
53
+ i2c mw 0x20 1 ff
54
+ run envboot
55
+ mmc dev 0
56
switch to partitions #0, OK
57
mmc0(part 0) is current device
58
+ mmc rescan
59
+ echo SD/MMC found on device 0
60
SD/MMC found on device 0
61
+ test -n 
62
+ run loadbootenv
63
+ fatload mmc 0 0x82000000 uEnv.txt
64
Can't set block device
65
+ test -n
66
+ run bootcmd_ti_mmc
67
+ run init_mmc
68
+ run args_all args_mmc
69
+ setenv optargs earlycon=ns16550a,mmio32,0x02800000 mtdparts=spi-nand0:512k(ospi_nand.tiboot3),2m(ospi_nand.tispl),4m(ospi_nand.u-boot),256k(ospi_nand.env),256k(ospi_nand.env.backup),98048k@32m(ospi_nand.rootfs),256k@130816k(ospi_nand.phypattern)
70
+ run finduuid
71
+ part uuid mmc 0 uuid
72
+ setenv bootargs console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000 mtdparts=spi-nand0:512k(ospi_nand.tiboot3),2m(ospi_nand.tispl),4m(ospi_nand.u-boot),256k(ospi_nand.env),256k(ospi_nand.env.backup),98048k@32m(ospi_nand.rootfs),256k@130816k(ospi_nand.phypattern) root=PARTUUID=13ce8ce8-3899-4f35-b870-5f9dcc0e7d05 rw rootfstype=ext4 rootwait
73
+ run update_do_main_cpsw0_qsgmii_phyinit
74
+ setenv do_main_cpsw0_qsgmii_phyinit 0
75
+ test 0 -eq 1
76
+ run boot_rprocs
77
+ test 1 -eq 1
78
+ test mmc = mmc
79
+ rproc init
80
+ run boot_rprocs_mmc
81
+ env set rproc_id
82
+ env set rproc_fw
83
+ env set secure_suffix
84
+ test 0 -eq 1
85
+ test -z 
86
+ env set rproc_id 0
87
+ test -z 0
88
+ env set rproc_fw /lib/firmware/am62a-mcu-r5f0_0-fw
89
+ run rproc_load_and_boot_one
90
+ load mmc 0 0x82000000 /lib/firmware/am62a-mcu-r5f0_0-fw
91
54164 bytes read in 5 ms (10.3 MiB/s)
92
+ rproc load 0 0x82000000 d394
93
Warning: Did not detect image signing certificate. Skipping authentication to prevent boot failure. This will fail on Security Enforcing(HS-SE) devices
94
Load Remote Processor 0 with data@addr=0x82000000 54164 bytes: Success!
95
+ rproc start 0
96
+ env set rproc_id
97
+ env set rproc_fw
98
+ test -z 
99
+ env set rproc_id 2
100
+ test -z 2
101
+ env set rproc_fw /lib/firmware/am62a-c71_0-fw
102
+ run rproc_load_and_boot_one
103
+ load mmc 0 0x82000000 /lib/firmware/am62a-c71_0-fw
104
19210280 bytes read in 110 ms (166.5 MiB/s)
105
+ rproc load 2 0x82000000 1252028
106
Warning: Did not detect image signing certificate. Skipping authentication to prevent boot failure. This will fail on Security Enforcing(HS-SE) devices
107
Load Remote Processor 2 with data@addr=0x82000000 19210280 bytes: Success!
108
+ rproc start 2
109
+ env set rproc_id
110
+ env set rproc_fw
111
+ test -z 
112
+ env set rproc_id
113
+ test -z 
114
+ env set rproc_id Boot
115
+ test -z Boot
116
+ env set rproc_fw rproc
117
+ run rproc_load_and_boot_one
118
+ load mmc 0 0x82000000 rproc
119
Failed to load 'rproc'
120
+ env set rproc_id
121
+ env set rproc_fw
122
+ test -z 
123
+ env set rproc_id in
124
+ test -z in
125
+ env set rproc_fw u-boot
126
+ run rproc_load_and_boot_one
127
+ load mmc 0 0x82000000 u-boot
128
Failed to load 'u-boot'
129
+ env set rproc_id
130
+ env set rproc_fw
131
+ test 0 -eq 1
132
+ run get_kern_mmc
133
+ load mmc 0 0x82000000 /boot/Image
134
29514240 bytes read in 162 ms (173.7 MiB/s)
135
+ run get_fdt_mmc
136
+ load mmc 0 0x88000000 /boot/dtb/ti/k3-am62a7-mitysom-tfc.dtb
137
64025 bytes read in 2 ms (30.5 MiB/s)
138
+ run get_overlay_mmc
139
+ fdt address 0x88000000
140
Working FDT set to 88000000
141
+ fdt resize 0x100000
142
+ run run_kern
143
+ booti 0x82000000 - 88000000
144
## Flattened Device Tree blob at 88000000
145
   Booting using the fdt blob at 0x88000000
146
Working FDT set to 88000000
147
   Loading Device Tree to 000000008feed000, end 000000008fffffff ... OK
148
Working FDT set to 8feed000
149

    
150
Starting kernel ...
151

    
152
[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
153
[    0.000000] Linux version 6.12.43-g-g26975df2e66f-dirty (oe-user@oe-host) (aarch64-oe-linux-gcc (GCC) 13.4.0, GNU ld (GNU Binutils) 2.42.0.20240723) #1 SMP PREEMPT Tue Dec 30 20:22:52 UTC 2025
154
[    0.000000] KASLR disabled due to lack of seed
155
[    0.000000] Machine model: Critical Link MitySOM-AM62A
156
[    0.000000] earlycon: ns16550a0 at MMIO32 0x0000000002800000 (options '')
157
[    0.000000] printk: legacy bootconsole [ns16550a0] enabled
158
[    0.000000] efi: UEFI not found.
159
[    0.000000] Reserved memory: created CMA memory pool at 0x00000000c0000000, size 576 MiB
160
[    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
161
[    0.000000] OF: reserved mem: 0x00000000c0000000..0x00000000e3ffffff (589824 KiB) map reusable linux,cma
162
[    0.000000] OF: reserved mem: 0x000000009e800000..0x000000009fffffff (24576 KiB) nomap non-reusable optee@9e800000
163
[    0.000000] OF: reserved mem: 0x0000000080000000..0x000000008007ffff (512 KiB) nomap non-reusable tfa@80000000
164
[    0.000000] Reserved memory: created DMA memory pool at 0x0000000099800000, size 1 MiB
165
[    0.000000] OF: reserved mem: initialized node c7x-dma-memory@99800000, compatible id shared-dma-pool
166
[    0.000000] OF: reserved mem: 0x0000000099800000..0x00000000998fffff (1024 KiB) nomap non-reusable c7x-dma-memory@99800000
167
[    0.000000] Reserved memory: created DMA memory pool at 0x0000000099900000, size 15 MiB
168
[    0.000000] OF: reserved mem: initialized node c7x-memory@99900000, compatible id shared-dma-pool
169
[    0.000000] OF: reserved mem: 0x0000000099900000..0x000000009a7fffff (15360 KiB) nomap non-reusable c7x-memory@99900000
170
[    0.000000] Reserved memory: created DMA memory pool at 0x000000009b800000, size 1 MiB
171
[    0.000000] OF: reserved mem: initialized node r5f-dma-memory@9b800000, compatible id shared-dma-pool
172
[    0.000000] OF: reserved mem: 0x000000009b800000..0x000000009b8fffff (1024 KiB) nomap non-reusable r5f-dma-memory@9b800000
173
[    0.000000] Reserved memory: created DMA memory pool at 0x000000009b900000, size 15 MiB
174
[    0.000000] OF: reserved mem: initialized node r5f-dma-memory@9b900000, compatible id shared-dma-pool
175
[    0.000000] OF: reserved mem: 0x000000009b900000..0x000000009c7fffff (15360 KiB) nomap non-reusable r5f-dma-memory@9b900000
176
[    0.000000] Reserved memory: created DMA memory pool at 0x000000009c800000, size 1 MiB
177
[    0.000000] OF: reserved mem: initialized node r5f-dma-memory@9c800000, compatible id shared-dma-pool
178
[    0.000000] OF: reserved mem: 0x000000009c800000..0x000000009c8fffff (1024 KiB) nomap non-reusable r5f-dma-memory@9c800000
179
[    0.000000] Reserved memory: created DMA memory pool at 0x000000009c900000, size 30 MiB
180
[    0.000000] OF: reserved mem: initialized node r5f-dma-memory@9c900000, compatible id shared-dma-pool
181
[    0.000000] OF: reserved mem: 0x000000009c900000..0x000000009e6fffff (30720 KiB) nomap non-reusable r5f-dma-memory@9c900000
182
[    0.000000] OF: reserved mem: 0x00000000a0000000..0x00000000a0ffffff (16384 KiB) nomap non-reusable edgeai-rtos-ipc-memory-region
183
[    0.000000] Reserved memory: created DMA memory pool at 0x00000000a1000000, size 32 MiB
184
[    0.000000] OF: reserved mem: initialized node edgeai-dma-memory@a1000000, compatible id shared-dma-pool
185
[    0.000000] OF: reserved mem: 0x00000000a1000000..0x00000000a2ffffff (32768 KiB) nomap non-reusable edgeai-dma-memory@a1000000
186
[    0.000000] OF: reserved mem: initialized node edgeai_shared-memories, compatible id dma-heap-carveout
187
[    0.000000] OF: reserved mem: 0x00000000a3000000..0x00000000adffffff (180224 KiB) map non-reusable edgeai_shared-memories
188
[    0.000000] Reserved memory: created DMA memory pool at 0x00000000ae000000, size 288 MiB
189
[    0.000000] OF: reserved mem: initialized node edgeai-core-heap-memory@ae000000, compatible id shared-dma-pool
190
[    0.000000] OF: reserved mem: 0x00000000ae000000..0x00000000bfffffff (294912 KiB) nomap non-reusable edgeai-core-heap-memory@ae000000
191
[    0.000000] Zone ranges:
192
[    0.000000]   DMA      [mem 0x0000000080000000-0x00000000ffffffff]
193
[    0.000000]   DMA32    empty
194
[    0.000000]   Normal   [mem 0x0000000100000000-0x00000008ffffffff]
195
[    0.000000] Movable zone start for each node
196
[    0.000000] Early memory node ranges
197
[    0.000000]   node   0: [mem 0x0000000080000000-0x000000008007ffff]
198
[    0.000000]   node   0: [mem 0x0000000080080000-0x00000000997fffff]
199
[    0.000000]   node   0: [mem 0x0000000099800000-0x000000009a7fffff]
200
[    0.000000]   node   0: [mem 0x000000009a800000-0x000000009b7fffff]
201
[    0.000000]   node   0: [mem 0x000000009b800000-0x000000009e6fffff]
202
[    0.000000]   node   0: [mem 0x000000009e700000-0x000000009e7fffff]
203
[    0.000000]   node   0: [mem 0x000000009e800000-0x00000000a2ffffff]
204
[    0.000000]   node   0: [mem 0x00000000a3000000-0x00000000adffffff]
205
[    0.000000]   node   0: [mem 0x00000000ae000000-0x00000000bfffffff]
206
[    0.000000]   node   0: [mem 0x00000000c0000000-0x00000000ffffffff]
207
[    0.000000]   node   0: [mem 0x0000000880000000-0x00000008ffffffff]
208
[    0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000008ffffffff]
209
[    0.000000] psci: probing for conduit method from DT.
210
[    0.000000] psci: PSCIv1.1 detected in firmware.
211
[    0.000000] psci: Using standard PSCI v0.2 function IDs
212
[    0.000000] psci: Trusted OS migration not required
213
[    0.000000] psci: SMC Calling Convention v1.5
214
[    0.000000] percpu: Embedded 32 pages/cpu s90328 r8192 d32552 u131072
215
[    0.000000] Detected VIPT I-cache on CPU0
216
[    0.000000] CPU features: detected: GIC system register CPU interface
217
[    0.000000] CPU features: detected: ARM erratum 845719
218
[    0.000000] alternatives: applying boot alternatives
219
[    0.000000] Kernel command line: console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000 mtdparts=spi-nand0:512k(ospi_nand.tiboot3),2m(ospi_nand.tispl),4m(ospi_nand.u-boot),256k(ospi_nand.env),256k(ospi_nand.env.backup),98048k@32m(ospi_nand.rootfs),256k@130816k(ospi_nand.phypattern) root=PARTUUID=13ce8ce8-3899-4f35-b870-5f9dcc0e7d05 rw rootfstype=ext4 rootwait
220
[    0.000000] Unknown kernel command line parameters "mtdparts=spi-nand0:512k(ospi_nand.tiboot3),2m(ospi_nand.tispl),4m(ospi_nand.u-boot),256k(ospi_nand.env),256k(ospi_nand.env.backup),98048k@32m(ospi_nand.rootfs),256k@130816k(ospi_nand.phypattern)", will be passed to user space.
221
[    0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
222
[    0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
223
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 1048576
224
[    0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off
225
[    0.000000] software IO TLB: area num 4.
226
[    0.000000] software IO TLB: mapped [mem 0x00000000fbfff000-0x00000000fffff000] (64MB)
227
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
228
[    0.000000] ftrace: allocating 49654 entries in 194 pages
229
[    0.000000] ftrace: allocated 194 pages with 3 groups
230
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
231
[    0.000000] rcu:     RCU event tracing is enabled.
232
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=4.
233
[    0.000000]  Trampoline variant of Tasks RCU enabled.
234
[    0.000000]  Rude variant of Tasks RCU enabled.
235
[    0.000000]  Tracing variant of Tasks RCU enabled.
236
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
237
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
238
[    0.000000] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
239
[    0.000000] RCU Tasks Rude: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
240
[    0.000000] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
241
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
242
[    0.000000] GICv3: GIC: Using split EOI/Deactivate mode
243
[    0.000000] GICv3: 256 SPIs implemented
244
[    0.000000] GICv3: 0 Extended SPIs implemented
245
[    0.000000] Root IRQ handler: gic_handle_irq
246
[    0.000000] GICv3: GICv3 features: 16 PPIs
247
[    0.000000] GICv3: GICD_CTRL.DS=0, SCR_EL3.FIQ=1
248
[    0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000001880000
249
[    0.000000] ITS [mem 0x01820000-0x0182ffff]
250
[    0.000000] GIC: enabling workaround for ITS: Socionext Synquacer pre-ITS
251
[    0.000000] ITS@0x0000000001820000: Devices Table too large, reduce ids 20->19
252
[    0.000000] ITS@0x0000000001820000: allocated 524288 Devices @880800000 (flat, esz 8, psz 64K, shr 0)
253
[    0.000000] ITS: using cache flushing for cmd queue
254
[    0.000000] GICv3: using LPI property table @0x00000008801b0000
255
[    0.000000] GIC: using cache flushing for LPI property table
256
[    0.000000] GICv3: CPU0: using allocated LPI pending table @0x00000008801c0000
257
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
258
[    0.000000] arch_timer: cp15 timer(s) running at 200.00MHz (phys).
259
[    0.000000] clocksource: arch_sys_counter: mask: 0x3ffffffffffffff max_cycles: 0x2e2049d3e8, max_idle_ns: 440795210634 ns
260
[    0.000001] sched_clock: 58 bits at 200MHz, resolution 5ns, wraps every 4398046511102ns
261
[    0.008750] Console: colour dummy device 80x25
262
[    0.013361] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=800000)
263
[    0.024048] pid_max: default: 32768 minimum: 301
264
[    0.028861] LSM: initializing lsm=capability,selinux
265
[    0.033998] SELinux:  Initializing.
266
[    0.038069] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
267
[    0.045653] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
268
[    0.056227] rcu: Hierarchical SRCU implementation.
269
[    0.061193] rcu:     Max phase no-delay instances is 1000.
270
[    0.066747] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level
271
[    0.075550] EFI services will not be available.
272
[    0.080474] smp: Bringing up secondary CPUs ...
273
[    0.085797] Detected VIPT I-cache on CPU1
274
[    0.085890] GICv3: CPU1: found redistributor 1 region 0:0x00000000018a0000
275
[    0.085909] GICv3: CPU1: using allocated LPI pending table @0x00000008801d0000
276
[    0.085967] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
277
[    0.086809] Detected VIPT I-cache on CPU2
278
[    0.086881] GICv3: CPU2: found redistributor 2 region 0:0x00000000018c0000
279
[    0.086897] GICv3: CPU2: using allocated LPI pending table @0x00000008801e0000
280
[    0.086939] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
281
[    0.087680] Detected VIPT I-cache on CPU3
282
[    0.087755] GICv3: CPU3: found redistributor 3 region 0:0x00000000018e0000
283
[    0.087770] GICv3: CPU3: using allocated LPI pending table @0x00000008801f0000
284
[    0.087805] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
285
[    0.087947] smp: Brought up 1 node, 4 CPUs
286
[    0.167699] SMP: Total of 4 processors activated.
287
[    0.172513] CPU: All CPU(s) started at EL2
288
[    0.176726] CPU features: detected: 32-bit EL0 Support
289
[    0.181989] CPU features: detected: CRC32 instructions
290
[    0.187297] alternatives: applying system-wide alternatives
291
[    0.193688] Memory: 2804488K/4194304K available (15232K kernel code, 2326K rwdata, 5608K rodata, 5504K init, 592K bss, 789600K reserved, 589824K cma-reserved)
292
[    0.209344] devtmpfs: initialized
293
[    0.222828] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
294
[    0.232854] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
295
[    0.256744] 25392 pages in range for non-PLT usage
296
[    0.256772] 516912 pages in range for PLT usage
297
[    0.262028] pinctrl core: initialized pinctrl subsystem
298
[    0.272663] DMI not present or invalid.
299
[    0.279012] NET: Registered PF_NETLINK/PF_ROUTE protocol family
300
[    0.286029] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations
301
[    0.293384] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
302
[    0.301483] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
303
[    0.309654] audit: initializing netlink subsys (disabled)
304
[    0.315421] audit: type=2000 audit(0.200:1): state=initialized audit_enabled=0 res=1
305
[    0.315913] thermal_sys: Registered thermal governor 'step_wise'
306
[    0.323362] thermal_sys: Registered thermal governor 'power_allocator'
307
[    0.329557] cpuidle: using governor menu
308
[    0.340434] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
309
[    0.347478] ASID allocator initialised with 65536 entries
310
[    0.358570] /bus@f0000/interrupt-controller@1800000: Fixed dependency cycle(s) with /bus@f0000/interrupt-controller@1800000
311
[    0.370770] /bus@f0000/bus@4000000/pinctrl@4084000: Fixed dependency cycle(s) with /bus@f0000/bus@4000000/pinctrl@4084000/mcu-gpio-p3-default-pins
312
[    0.384228] /bus@f0000/bus@4000000/pinctrl@4084000: Fixed dependency cycle(s) with /bus@f0000/bus@4000000/pinctrl@4084000/mcu-uart1-default-pins
313
[    0.397491] /bus@f0000/bus@4000000/pinctrl@4084000: Fixed dependency cycle(s) with /bus@f0000/bus@4000000/pinctrl@4084000/mcu_system_pins_default
314
[    0.410842] /bus@f0000/bus@4000000/pinctrl@4084000: Fixed dependency cycle(s) with /bus@f0000/bus@4000000/pinctrl@4084000/jtag-default-pins
315
[    0.427890] /bus@f0000/pinctrl@f4000: Fixed dependency cycle(s) with /bus@f0000/pinctrl@f4000/gpio-p3-default-pins
316
[    0.438511] /bus@f0000/pinctrl@f4000: Fixed dependency cycle(s) with /bus@f0000/pinctrl@f4000/main-system-default-pins
317
[    0.456035] /bus@f0000/dwc3-usb@f900000/usb@31000000: Fixed dependency cycle(s) with /usb_microb_connector
318
[    0.466033] /usb_microb_connector: Fixed dependency cycle(s) with /bus@f0000/dwc3-usb@f900000/usb@31000000
319
[    0.477153] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages
320
[    0.484150] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page
321
[    0.490565] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages
322
[    0.497507] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page
323
[    0.503918] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages
324
[    0.510860] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page
325
[    0.517271] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages
326
[    0.524213] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page
327
[    0.532635] k3-chipinfo 43000014.chipid: Family:AM62AX rev:SR1.0 JTAGID[0x0bb8d02f] Detected
328
[    0.543646] iommu: Default domain type: Translated
329
[    0.548602] iommu: DMA domain TLB invalidation policy: strict mode
330
[    0.562852] SCSI subsystem initialized
331
[    0.567123] usbcore: registered new interface driver usbfs
332
[    0.572781] usbcore: registered new interface driver hub
333
[    0.578256] usbcore: registered new device driver usb
334
[    0.584016] pps_core: LinuxPPS API ver. 1 registered
335
[    0.589102] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
336
[    0.598455] PTP clock support registered
337
[    0.602500] EDAC MC: Ver: 3.0.0
338
[    0.606085] scmi_core: SCMI protocol bus registered
339
[    0.611400] FPGA manager framework
340
[    0.614968] Advanced Linux Sound Architecture Driver Initialized.
341
[    0.622450] clocksource: Switched to clocksource arch_sys_counter
342
[    0.629162] VFS: Disk quotas dquot_6.6.0
343
[    0.633216] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
344
[    0.648097] Carveout Heap: Exported 176 MiB at 0x00000000a3000000
345
[    0.654466] NET: Registered PF_INET protocol family
346
[    0.659680] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear)
347
[    0.670246] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
348
[    0.679069] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
349
[    0.687008] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
350
[    0.695325] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear)
351
[    0.703829] TCP: Hash tables configured (established 32768 bind 32768)
352
[    0.710714] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
353
[    0.717663] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
354
[    0.725208] NET: Registered PF_UNIX/PF_LOCAL protocol family
355
[    0.731577] RPC: Registered named UNIX socket transport module.
356
[    0.737660] RPC: Registered udp transport module.
357
[    0.742482] RPC: Registered tcp transport module.
358
[    0.747310] RPC: Registered tcp-with-tls transport module.
359
[    0.752921] RPC: Registered tcp NFSv4.1 backchannel transport module.
360
[    0.759526] NET: Registered PF_XDP protocol family
361
[    0.764451] PCI: CLS 0 bytes, default 64
362
[    0.770022] Initialise system trusted keyrings
363
[    0.774892] workingset: timestamp_bits=46 max_order=20 bucket_order=0
364
[    0.781834] squashfs: version 4.0 (2009/01/31) Phillip Lougher
365
[    0.788142] NFS: Registering the id_resolver key type
366
[    0.793356] Key type id_resolver registered
367
[    0.797636] Key type id_legacy registered
368
[    0.801758] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
369
[    0.808616] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
370
[    0.872813] Key type asymmetric registered
371
[    0.877025] Asymmetric key parser 'x509' registered
372
[    0.882090] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
373
[    0.889910] io scheduler mq-deadline registered
374
[    0.894556] io scheduler kyber registered
375
[    0.898692] io scheduler bfq registered
376
[    0.909695] pinctrl-single 4084000.pinctrl: 34 pins, size 136
377
[    0.916409] pinctrl-single f4000.pinctrl: 151 pins, size 604
378
[    0.923981] ledtrig-cpu: registered to indicate activity on CPUs
379
[    0.937086] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
380
[    0.953191] loop: module loaded
381
[    0.957608] megasas: 07.727.03.00-rc1
382
[    0.965777] tun: Universal TUN/TAP device driver, 1.6
383
[    0.972185] VFIO - User Level meta-driver version: 0.3
384
[    0.978940] usbcore: registered new interface driver usb-storage
385
[    0.985877] i2c_dev: i2c /dev entries driver
386
[    0.992113] sdhci: Secure Digital Host Controller Interface driver
387
[    0.998468] sdhci: Copyright(c) Pierre Ossman
388
[    1.003190] sdhci-pltfm: SDHCI platform and OF driver helper
389
[    1.009741] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
390
[    1.017270] usbcore: registered new interface driver usbhid
391
[    1.022981] usbhid: USB HID core driver
392
[    1.028498] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 (0,8000003f) counters available
393
[    1.038913] optee: probing for conduit method.
394
[    1.043494] optee: revision 4.6 (71785645fa6ce42d)
395
[    1.043904] optee: dynamic shared memory is enabled
396
[    1.054608] optee: initialized driver
397
[    1.054723] random: crng init done
398
[    1.060660] Initializing XFRM netlink socket
399
[    1.066248] NET: Registered PF_PACKET protocol family
400
[    1.071512] Key type dns_resolver registered
401
[    1.084993] registered taskstats version 1
402
[    1.089588] Loading compiled-in X.509 certificates
403
[    1.106162] ti-sci 44043000.system-controller: ABI: 4.0 (firmware rev 0x000b '11.1.5--v11.01.05 (Fancy Rat)')
404
[    1.160265] /bus@f0000/i2c@20000000/pmic@30: Fixed dependency cycle(s) with /bus@f0000/i2c@20000000/pmic@30/regulators/buck2
405
[    1.187410] omap_i2c 20000000.i2c: bus 0 rev0.12 at 400 kHz
406
[    1.193968] ti-sci-intr 4210000.interrupt-controller: Interrupt Router 5 domain created
407
[    1.202334] ti-sci-intr bus@f0000:interrupt-controller@a00000: Interrupt Router 3 domain created
408
[    1.211625] ti-sci-inta 48000000.interrupt-controller: Interrupt Aggregator domain 28 created
409
[    1.220655] ti-sci-inta 4e0a0000.interrupt-controller: Interrupt Aggregator domain 200 created
410
[    1.231522] ti-udma 485c0100.dma-controller: Number of rings: 82
411
[    1.240383] ti-udma 485c0100.dma-controller: Channels: 48 (bchan: 18, tchan: 12, rchan: 18)
412
[    1.251617] ti-udma 485c0000.dma-controller: Number of rings: 150
413
[    1.262864] ti-udma 485c0000.dma-controller: Channels: 35 (tchan: 20, rchan: 15)
414
[    1.272520] ti-udma 4e230000.dma-controller: Number of rings: 6
415
[    1.279240] ti-udma 4e230000.dma-controller: Channels: 6 (bchan: 0, tchan: 0, rchan: 6)
416
[    1.288935] printk: legacy console [ttyS2] disabled
417
[    1.294323] 2800000.serial: ttyS2 at MMIO 0x2800000 (irq = 247, base_baud = 3000000) is a 8250
418
[    1.303316] printk: legacy console [ttyS2] enabled
419
[    1.303316] printk: legacy console [ttyS2] enabled
420
[    1.313006] printk: legacy bootconsole [ns16550a0] disabled
421
[    1.313006] printk: legacy bootconsole [ns16550a0] disabled
422
[    1.329358] am65-cpsw-nuss 8000000.ethernet: initializing am65 cpsw nuss version 0x6BA01103, cpsw version 0x6BA81103 Ports: 3 quirks:00000006
423
[    1.342582] am65-cpsw-nuss 8000000.ethernet: Use random MAC address
424
[    1.382484] davinci_mdio 8000f00.mdio: davinci mdio revision 9.7, bus freq 1000000
425
[    1.398119] davinci_mdio 8000f00.mdio: phy[3]: device 8000f00.mdio:03, driver Microchip KSZ9131 Gigabit PHY
426
[    1.407932] davinci_mdio 8000f00.mdio: phy[4]: device 8000f00.mdio:04, driver Microchip KSZ9131 Gigabit PHY
427
[    1.417914] am65-cpsw-nuss 8000000.ethernet: initialized cpsw ale version 1.5
428
[    1.425070] am65-cpsw-nuss 8000000.ethernet: ALE Table size 512, Policers 32
429
[    1.433140] am65-cpsw-nuss 8000000.ethernet: CPTS ver 0x4e8a010c, freq:500000000, add_val:1 pps:1
430
[    1.447354] am65-cpsw-nuss 8000000.ethernet: set new flow-id-base 19
431
[    1.458783] /usb_microb_connector: Fixed dependency cycle(s) with /bus@f0000/dwc3-usb@f900000/usb@31000000
432
[    1.468664] /bus@f0000/dwc3-usb@f900000/usb@31000000: Fixed dependency cycle(s) with /usb_microb_connector
433
[    1.485184] core: _opp_supported_by_regulators: OPP minuV: 850000 maxuV: 850000, not supported by regulator
434
[    1.494956] cpu cpu0: _opp_add: OPP not supported by regulators (1400000000)
435
[    1.502873] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 1200000 KHz, changing to: 1250000 KHz
436
[    1.515507] mmc0: CQHCI version 5.10
437
[    1.526826] input: tps65219-pwrbutton as /devices/platform/bus@f0000/20000000.i2c/i2c-0/0-0030/tps65219-pwrbutton.2.auto/input/input0
438
[    1.544518] mmc1: CQHCI version 5.10
439
[    1.545754] clk: Disabling unused clocks
440
[    1.556547] PM: genpd: Disabling unused power domains
441
[    1.558461] mmc0: SDHCI controller on fa10000.mmc [fa10000.mmc] using ADMA 64-bit
442
[    1.561747] ALSA device list:
443
[    1.572129]   No soundcards found.
444
[    1.613740] mmc0: Command Queue Engine enabled
445
[    1.618224] mmc0: new HS200 MMC card at address 0001
446
[    1.623816] mmcblk0: mmc0:0001 IY2964 58.3 GiB
447
[    1.631130]  mmcblk0: p1
448
[    1.634140] mmcblk0boot0: mmc0:0001 IY2964 4.00 MiB
449
[    1.640043] mmcblk0boot1: mmc0:0001 IY2964 4.00 MiB
450
[    1.646040] mmcblk0rpmb: mmc0:0001 IY2964 4.00 MiB, chardev (239:0)
451
[    3.066133] sdhci-am654 fa00000.mmc: Power on failed
452
[    3.101739] mmc1: SDHCI controller on fa00000.mmc [fa00000.mmc] using ADMA 64-bit
453
[    3.342615] EXT4-fs (mmcblk0p1): recovery complete
454
[    3.347610] EXT4-fs (mmcblk0p1): mounted filesystem 07a119d8-8473-429b-a853-d964f42d92f1 r/w with ordered data mode. Quota mode: none.
455
[    3.359798] VFS: Mounted root (ext4 filesystem) on device 179:1.
456
[    3.367091] devtmpfs: mounted
457
[    3.374126] Freeing unused kernel memory: 5504K
458
[    3.378852] Run /sbin/init as init process
459
[    3.485713] systemd[1]: System time before build time, advancing clock.
460
[    3.518277] NET: Registered PF_INET6 protocol family
461
[    3.524459] Segment Routing with IPv6
462
[    3.528214] In-situ OAM (IOAM) with IPv6
463
[    3.556011] systemd[1]: systemd 255.21^ running in system mode (+PAM -AUDIT -SELINUX -APPARMOR +IMA -SMACK +SECCOMP -GCRYPT -GNUTLS -OPENSSL +ACL +BLKID -CURL -ELFUTILS -FIDO2 -IDN2 -IDN -IPTC +KMOD -LIBCRYPTSETUP +LIBFDISK -PCRE2 -PWQUALITY -P11KIT -QRENCODE -TPM2 -BZIP2 -LZ4 -XZ -ZLIB +ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified)
464
[    3.587920] systemd[1]: Detected architecture arm64.
465

    
466
Welcome to Arago 2025.01!
467

    
468
[    3.604321] systemd[1]: Hostname set to <mitysom-am62ax-tfc>.
469
[    4.041860] systemd[1]: Queued start job for default target Multi-User System.
470
[    4.084959] systemd[1]: Created slice Slice /system/getty.
471
[  OK  ] Created slice Slice /system/getty.
472
[    4.105115] systemd[1]: Created slice Slice /system/modprobe.
473
[  OK  ] Created slice Slice /system/modprobe.
474
[    4.125186] systemd[1]: Created slice Slice /system/serial-getty.
475
[  OK  ] Created slice Slice /system/serial-getty.
476
[    4.144615] systemd[1]: Created slice User and Session Slice.
477
[  OK  ] Created slice User and Session Slice.
478
[    4.162992] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
479
[  OK  ] Started Dispatch Password Requests to Console Directory Watch.
480
[    4.182866] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
481
[  OK  ] Started Forward Password Requests to Wall Directory Watch.
482
[    4.202688] systemd[1]: Expecting device /dev/fb0...
483
         Expecting device /dev/fb0...
484
[    4.214574] systemd[1]: Expecting device /dev/ttyS2...
485
         Expecting device /dev/ttyS2...
486
[    4.226709] systemd[1]: Reached target Path Units.
487
[  OK  ] Reached target Path Units.
488
[    4.238614] systemd[1]: Reached target Remote File Systems.
489
[  OK  ] Reached target Remote File Systems.
490
[    4.254604] systemd[1]: Reached target Slice Units.
491
[  OK  ] Reached target Slice Units.
492
[    4.266613] systemd[1]: Reached target Swaps.
493
[  OK  ] Reached target Swaps.
494
[    4.333654] systemd[1]: Listening on RPCbind Server Activation Socket.
495
[  OK  ] Listening on RPCbind Server Activation Socket.
496
[    4.350802] systemd[1]: Reached target RPC Port Mapper.
497
[  OK  ] Reached target RPC Port Mapper.
498
[    4.378063] systemd[1]: Listening on Process Core Dump Socket.
499
[  OK  ] Listening on Process Core Dump Socket.
500
[    4.395138] systemd[1]: Listening on initctl Compatibility Named Pipe.
501
[  OK  ] Listening on initctl Compatibility Named Pipe.
502
[    4.416044] systemd[1]: Listening on Journal Audit Socket.
503
[  OK  ] Listening on Journal Audit Socket.
504
[    4.435445] systemd[1]: Listening on Journal Socket (/dev/log).
505
[  OK  ] Listening on Journal Socket (/dev/log).
506
[    4.455465] systemd[1]: Listening on Journal Socket.
507
[  OK  ] Listening on Journal Socket.
508
[    4.467643] systemd[1]: Listening on Network Service Netlink Socket.
509
[  OK  ] Listening on Network Service Netlink Socket.
510
[    4.492050] systemd[1]: Listening on udev Control Socket.
511
[  OK  ] Listening on udev Control Socket.
512
[    4.511328] systemd[1]: Listening on udev Kernel Socket.
513
[  OK  ] Listening on udev Kernel Socket.
514
[    4.531345] systemd[1]: Listening on User Database Manager Socket.
515
[  OK  ] Listening on User Database Manager Socket.
516
[    4.594890] systemd[1]: Mounting Huge Pages File System...
517
         Mounting Huge Pages File System...
518
[    4.611493] systemd[1]: Mounting POSIX Message Queue File System...
519
         Mounting POSIX Message Queue File System...
520
[    4.635643] systemd[1]: Mounting Kernel Debug File System...
521
         Mounting Kernel Debug File System...
522
[    4.659701] systemd[1]: Mounting Kernel Trace File System...
523
         Mounting Kernel Trace File System...
524
[    4.689071] systemd[1]: Mounting Temporary Directory /tmp...
525
         Mounting Temporary Directory /tmp...
526
[    4.709225] systemd[1]: Starting Create List of Static Device Nodes...
527
         Starting Create List of Static Device Nodes...
528
[    4.732121] systemd[1]: Starting Load Kernel Module configfs...
529
         Starting Load Kernel Module configfs...
530
[    4.752159] systemd[1]: Starting Load Kernel Module drm...
531
         Starting Load Kernel Module drm...
532
[    4.776010] systemd[1]: Starting Load Kernel Module fuse...
533
         Starting Load Kernel Module fuse...
534
[    4.802222] systemd[1]: Starting RPC Bind...
535
         Starting RPC Bind...
536
[    4.815174] systemd[1]: File System Check on Root Device was skipped because of an unmet condition check (ConditionPathIsReadWrite=!/).
537
[    4.816835] fuse: init (API version 7.41)
538
[    4.836989] systemd[1]: Starting Journal Service...
539
         Starting Journal Service...
540
[    4.859656] systemd[1]: Starting Load Kernel Modules...
541
         Starting Load Kernel Modules...
542
[    4.877106] systemd[1]: Starting Generate network units from Kernel command line...
543
         Starting Generate network units from Kernel command line...
544
[    4.907379] systemd[1]: Starting Remount Root and Kernel File Systems...
545
[    4.913005] cryptodev: loading out-of-tree module taints kernel.
546
         Starting Remount Root and Kernel File Systems sysctl table check failed: ioctl/(null) procname is null
547
[0m...
548
[    4.933022] sysctl table check failed: ioctl/(null) No proc_handler
549
[    4.939652] cryptodev: driver 1.14 loaded.
550
[    4.943253] systemd-journald[132]: Collecting audit messages is enabled.
551
[    4.967358] systemd[1]: Starting Coldplug All udev Devices...
552
         Starting Coldplug All udev Devices...
553
[    4.996619] systemd[1]: Started RPC Bind.
554
[  OK  ] Started RPC Bind.
555
[    5.013839] systemd[1]: Mounted Huge Pages File System.
556
[  OK  ] Mounted Huge Pages File System.
557
[    5.031379] systemd[1]: Started Journal Service.
558
[    5.038979] EXT4-fs (mmcblk0p1): re-mounted 07a119d8-8473-429b-a853-d964f42d92f1.
559

    
560
[  OK  ] Mounted POSIX Message Queue File System.
561
[  OK  ] Mounted Kernel Debug File System.
562
[  OK  ] Mounted Kernel Trace File System.
563
[  OK  ] Mounted Temporary Directory /tmp.
564
[  OK  ] Finished Create List of Static Device Nodes.
565
[  OK  ] Finished Load Kernel Module configfs.
566
[  OK  ] Finished Load Kernel Module drm.
567
[  OK  ] Finished Load Kernel Module fuse.
568
[  OK  ] Finished Load Kernel Modules.
569
[  OK  ] Finished Generate network units from Kernel command line.
570
[  OK  ] Finished Remount Root and Kernel File Systems.
571
         Mounting FUSE Control File System...
572
         Mounting Kernel Configuration File System...
573
         Starting Flush Journal to Persistent Storage...
574
         Starting Apply Kernel Variables...
575
         Starting Create Static Device Nodes in /dev gracefully...
576
[  OK  ] Mounted FUSE Control File System    5.349828] systemd-journald[132]: Received client request to flush runtime journal.
577
m.
578
[  OK  ] Mounted Kernel Configuration File System.
579
[  OK  ] Finished Flush Journal to Persistent Storage.
580
[  OK  ] Finished Apply Kernel Variables.
581
[  OK  ] Finished Create Static Device Nodes in /dev gracefully.
582
         Starting Create Static Device Nodes in /dev...
583
[  OK  ] Finished Create Static Device Nodes in /dev.
584
[  OK  ] Reached target Preparation for Local File Systems.
585
         Mounting /var/volatile...
586
[    5.554831] audit: type=1334 audit(1748544504.068:2): prog-id=6 op=LOAD
587
[    5.562789] audit: type=1334 audit(1748544504.072:3): prog-id=7 op=LOAD
588
         Starting Rule-based Manager for Device Events and Files...
589
[  OK  ] Mounted /var/volatile.
590
         Starting Load/Save OS Random Seed...
591
[  OK  ] Reached target Local File Systems.
592
         Starting Create System Files and Directories...
593
[  OK  ] Finished Coldplug All udev Devices.
594
[  OK  ] Finished Load/Save OS Random Seed.
595
[    5.761182] audit: type=1334 audit(1748544504.272:4): prog-id=8 op=LOAD
596
[    5.767938] audit: type=1334 audit(1748544504.280:5): prog-id=9 op=LOAD
597
[    5.774711] audit: type=1334 audit(1748544504.288:6): prog-id=10 op=LOAD
598
         Starting User Database Manager...
599
[  OK  ] Finished Create System Files and Directories.
600
[    5.850559] audit: type=1334 audit(1748544504.360:7): prog-id=11 op=LOAD
601
         Starting Network Name Resolution...
602
[    5.891495] audit: type=1334 audit(1748544504.404:8): prog-id=12 op=LOAD
603
         Starting Network Time Synchronization...
604
         Starting Record System Boot/Shutdown in UTMP...
605
[  OK  ] Started User Database Manager.
606
[  OK  ] Started Rule-based Manager for Device Events and Files.
607
[  OK  ] Finished Record System Boot/Shutdown in UTMP.
608
[  OK  ] Started Network Time Synchronization.
609
[  OK  ] Started Network Name Resolution.
610
[  OK  ] Reached target Host and Network Name Lookups.
611
[  OK  ] Reached target System Initialization.
612
[  OK  ] Started Daily Cleanup of Temporary Directories.
613
[  OK  ] Reached target System Time Set.
614
[  OK  ] Reached target Timer Units.
615
[  OK  ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket.
616
[  OK  ] Listening on D-Bus System Message Bus Socket.
617
         Starting Docker Socket for the API...
618
[  OK  ] Listening on dropbear.socket.
619
[    6.440125] audit: type=1334 audit(1748556837.800:9): prog-id=13 op=LOAD
620
         Starting D-Bus System Message Bus...
621
         Starting Reboot and dump vmcore via kexec...
622
[  OK  ] Listening on Docker Socket for the API.
623
[  OK  ] Found device /dev/ttyS2.
624
[  OK  ] Finished Reboot and dump vmcore via kexec.
625
[  OK  ] Started D-Bus System Message Bus.
626
[  OK  ] Reached target Socket Units.
627
[  OK  ] Reached target Basic System.
628
         Starting Avahi mDNS/DNS-SD Stack...
629
         Starting Print notice about GPLv3 packages...
630
         Starting IPv6 Packet Filtering Framework...
631
         Starting IPv4 Packet Filtering Framework...
632
[  OK  ] Started irqbalance daemon.
633
[  OK  ] Started strongSwan IPsec IKEv1/IKEv2 daemon using ipsec.conf.
634
[    6.921455] audit: type=1334 audit(1748556838.280:10): prog-id=14 op=LOAD
635
[    6.933552] audit: type=1334 audit(1748556838.292:11): prog-id=15 op=LOAD
636
         Starting User Login Management...
637
         Starting Telnet Server...
638
[  OK  ] Finished IPv6 Packet Filtering Framework.
639
[  OK  ] Finished IPv4 Packet Filtering Framework.
640
[  OK  ] Finished Telnet Server.
641
[  OK  ] Reached target Preparation for Network.
642
         Starting Network Configuration...
643
[  OK  ] Started Avahi mDNS/DNS-SD Stack.
644
[    7.203529] mc: Linux media interface: v0.10
645
[    7.237309] omap-mailbox 29000000.mailbox: omap mailbox rev 0x66fca100
646
[    7.264073] videodev: Linux video capture interface: v2.00
647
[    7.276656] omap-mailbox 29010000.mailbox: omap mailbox rev 0x66fca100
648
[    7.294384] omap-mailbox 29020000.mailbox: omap mailbox rev 0x66fca100
649
[    7.301711] k3-dsp-rproc 7e000000.dsp: assigned reserved memory node c7x-dma-memory@99800000
650
[    7.311497] k3-dsp-rproc 7e000000.dsp: configured DSP for IPC-only mode
651
[    7.318852] remoteproc remoteproc0: 7e000000.dsp is available
652
[    7.325015] remoteproc remoteproc0: attaching to 7e000000.dsp
653
[    7.331567] rproc-virtio rproc-virtio.3.auto: assigned reserved memory node c7x-dma-memory@99800000
654
[    7.341665] virtio_rpmsg_bus virtio0: rpmsg host is online
655
[    7.343025] virtio_rpmsg_bus virtio0: creating channel rpmsg_chrdev addr 0xd
656
[    7.347326] rproc-virtio rproc-virtio.3.auto: registered virtio0 (type 7)
657
[    7.361436] remoteproc remoteproc0: remote processor 7e000000.dsp is now attached
658
[    7.372112] omap-mailbox 29030000.mailbox: no available mbox devices found
659
[  OK  ] Started User Login Management.
660
[    7.521720] at24 0-0050: supply vcc not found, using dummy regulator
661
[    7.545775] at24 0-0050: 4096 byte 24c32 EEPROM, read-only
662
[    7.551907] cfg80211: Loading compiled-in X.509 certificates for regulatory database
663
[    7.554893] rtc-ti-k3 2b1f0000.rtc: registered as rtc0
664
[    7.579051] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
665
[    7.585828] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600'
666
[    7.593899] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
667
[    7.604443] cfg80211: failed to load regulatory.db
668
[    7.619317] vdec 30210000.video-codec: error -ENXIO: IRQ index 0 not found
669
[    7.621747] platform 79000000.r5f: configured R5F for IPC-only mode
670
[    7.626603] vdec 30210000.video-codec: failed to get irq resource, falling back to polling
671
[    7.637346] platform 79000000.r5f: assigned reserved memory node r5f-dma-memory@9b800000
672
[    7.652392] vdec 30210000.video-codec: OPP table not found in device tree
673
[    7.663094] remoteproc remoteproc1: 79000000.r5f is available
674
[    7.669099] remoteproc remoteproc1: attaching to 79000000.r5f
675
[    7.686913] vdec 30210000.video-codec: Added wave5 driver with caps: 'ENCODE' 'DECODE'
676
[    7.687580] e5010 fd20000.jpeg-encoder: Device registered as /dev/video2
677
[    7.694950] vdec 30210000.video-codec: Product Code:      0x521c
678
[    7.707848] vdec 30210000.video-codec: Firmware Revision: 363254
679
[  OK  ] Started Network Configuration.
680
[  OK  ] Reached target Network.
681
[    7.766820] rproc-virtio rproc-virtio.5.auto: assigned reserved memory node r5f-dma-memory@9b800000
682
         Starting containerd container runtime...
683
         Starting LLDP daemon...
684
[  OK  ] Started Netperf Benchmark Server.
685
[    7.856486] am65-cpsw-nuss 8000000.ethernet eth0: PHY [8000f00.mdio:03] driver [Microchip KSZ9131 Gigabit PHY] (irq=POLL)
686
[    7.868193] am65-cpsw-nuss 8000000.ethernet eth0: configuring for phy/rgmii-rxid link mode
687
         Starting Simple Network Management Protocol (SNMP) Daemon....
688
[    7.888450] virtio_rpmsg_bus virtio1: rpmsg host is online
689
[    7.889210] virtio_rpmsg_bus virtio1: creating channel ti.ipc4.ping-pong addr 0xd
690
[    7.902305] virtio_rpmsg_bus virtio1: creating channel rpmsg_chrdev addr 0xe
691
         Starting Permit User Sessions...
692
[  OK  ] Reached target Hardware activated USB gadget.
693
[    7.971061] rproc-virtio rproc-virtio.5.auto: registered virtio1 (type 7)
694
[    7.978077] remoteproc remoteproc1: remote processor 79000000.r5f is now attached
695
[  OK  ] Finished Permit User Sessions.
696
[    8.083996] am65-cpsw-nuss 8000000.ethernet eth1: PHY [8000f00.mdio:04] driver [Microchip KSZ9131 Gigabit PHY] (irq=POLL)
697
[    8.107373] am65-cpsw-nuss 8000000.ethernet eth1: configuring for phy/rgmii-rxid link mode
698
[    8.118209] platform 78000000.r5f: R5F core may have been powered on by a different host, programmed state (0) != actual state (1)
699
[  OK  ] Started Getty on tty1.
700
[    8.135002] platform 78000000.r5f: configured R5F for IPC-only mode
701
[    8.143274] platform 78000000.r5f: assigned reserved memory node r5f-dma-memory@9c800000
702
[  OK  ] Started Serial Getty on ttyS2.
703
[  OK  ] Reached target Login Prompts.
704
[    8.210741] remoteproc remoteproc2: 78000000.r5f is available
705
[    8.218097] remoteproc remoteproc2: attaching to 78000000.r5f
706
[    8.232788] rproc-virtio rproc-virtio.6.auto: assigned reserved memory node r5f-dma-memory@9c800000
707
[    8.253910] virtio_rpmsg_bus virtio2: rpmsg host is online
708
[    8.255104] virtio_rpmsg_bus virtio2: creating channel rpmsg_chrdev addr 0xd
709
[    8.266903] virtio_rpmsg_bus virtio2: creating channel rpmsg_chrdev addr 0xe
710
[    8.267072] virtio_rpmsg_bus virtio2: creating channel ti.ipc4.ping-pong addr 0x15
711
[  OK  ] Started LLDP daemon.
712
[    8.270807] rproc-virtio rproc-virtio.6.auto: registered virtio2 (type 7)
713
[    8.270829] remoteproc remoteproc2: remote processor 78000000.r5f is now attached
714
[    8.301793] virtio_rpmsg_bus virtio2: msg received with no recipient
715
[    8.308528] virtio_rpmsg_bus virtio0: creating channel rpmsg_chrdev addr 0xe
716
[    8.320186] virtio_rpmsg_bus virtio0: creating channel ti.ipc4.ping-pong addr 0x15
717
[    8.338154] virtio_rpmsg_bus virtio0: msg received with no recipient
718
[  OK  ] Created slice Slice /system/tee-supplicant.
719
[  OK  ] Started TEE Supplicant on teepriv0.
720
         Starting Virtual Console Setup...
721
[  OK  ] Started Simple Network Management Protocol (SNMP) Daemon..
722
[  OK  ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.
723
[  OK  ] Finished Virtual Console Setup.
724
***************************************************************
725
***************************************************************
726
NOTICE: This file system contains the following GPL-3.0 packages:
727
        bash
728
        binutils
729
        cifs-utils
730
        dosfstools
731
        gdbserver
732
        grub-common
733
        grub-editenv
734
        grub-efi
735
        hidapi
736
        kbd-keymaps-pine
737
        less
738
        libbfd
739
        libdebuginfod1
740
        libdw1
741
        libelf1
742
        libgcc1
743
        libopcodes
744
        libreadline8
745
        libstdc++6
746
        parted
747
        rsync
748

    
749
If you do not wish to distribute GPL-3.0 components please remove
750
the above packages prior to distribution.  This can be done using
751
the opkg remove command.  i.e.:
752
    opkg remove <package>
753
Where <package> is the name printed in the list above
754

    
755
NOTE: If the package is a dependency of another package you
756
      will be notified of the dependent packages.  You should
757
      use the --force-removal-of-dependent-packages option to
758
      also remove the dependent packages as well
759
***************************************************************
760
***************************************************************
761
[  OK  ] Finished Print notice about GPLv3 packages.
762
[  OK  ] Started containerd container runtime.
763
[  OK  ] Reached target Multi-User System.
764
         Starting Record Runlevel Change in UTMP...
765
[  OK  ] Finished Record Runlevel Change in UTMP.
766
[   12.233708] am65-cpsw-nuss 8000000.ethernet eth1: Link is Up - 1Gbps/Full - flow control rx/tx
767

    
768
 _____                    _____           _         _   
769
|  _  |___ ___ ___ ___   |  _  |___ ___  |_|___ ___| |_ 
770
|     |  _| .'| . | . |  |   __|  _| . | | | -_|  _|  _|
771
|__|__|_| |__,|_  |___|  |__|  |_| |___|_| |___|___|_|  
772
              |___|                    |___|            
773

    
774
Arago Project mitysom-am62ax-tfc ttyS2
775

    
776
Arago 2025.01 mitysom-am62ax-tfc ttyS2
777

    
778
mitysom-am62ax-tfc login: root
779
[   16.801445] kauditd_printk_skb: 2 callbacks suppressed
780
[   16.801465] audit: type=1006 audit(1748556848.160:14): pid=510 uid=0 subj=kernel old-auid=4294967295 auid=0 tty=(none) old-ses=4294967295 ses=1 res=1
781
[   16.820189] audit: type=1300 audit(1748556848.160:14): arch=c00000b7 syscall=64 success=yes exit=1 a0=8 a1=ffffe7c0a7f8 a2=1 a3=1 items=0 ppid=1 pid=510 auid=0 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=1 comm="(systemd)" exe="/usr/lib/systemd/systemd-executor" subj=kernel key=(null)
782
[   16.847781] audit: type=1327 audit(1748556848.160:14): proctitle="(systemd)"
783
[   16.895626] audit: type=1334 audit(1748556848.256:15): prog-id=18 op=LOAD
784
[   16.902490] audit: type=1300 audit(1748556848.256:15): arch=c00000b7 syscall=280 success=yes exit=8 a0=5 a1=ffffca867768 a2=90 a3=0 items=0 ppid=1 pid=510 auid=0 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=1 comm="systemd" exe="/usr/lib/systemd/systemd" subj=kernel key=(null)
785
[   16.929328] audit: type=1327 audit(1748556848.256:15): proctitle="(systemd)"
786
[   16.936489] audit: type=1334 audit(1748556848.256:16): prog-id=18 op=UNLOAD
787
[   16.943526] audit: type=1300 audit(1748556848.256:16): arch=c00000b7 syscall=57 success=yes exit=0 a0=8 a1=1 a2=0 a3=ffffbf0dfc60 items=0 ppid=1 pid=510 auid=0 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=1 comm="systemd" exe="/usr/lib/systemd/systemd" subj=kernel key=(null)
788
[   16.970168] audit: type=1327 audit(1748556848.256:16): proctitle="(systemd)"
789
[   16.977294] audit: type=1334 audit(1748556848.256:17): prog-id=19 op=LOAD
790
root@mitysom-am62ax-tfc:~# find /sys/firmware | grep uart5
791
/sys/firmware/devicetree/base/__symbols__/main_uart5
792
root@mitysom-am62ax-tfc:~# [   31.974775] UNUSED: disabling
(1-1/2) Go to top
Add picture from clipboard (Maximum size: 1 GB)