Mity CPU Platforms » MityDSP-L138 (ARM9 Based Platforms)

08/18/2010

04:16 PM Software Development: RE: Loading FPGA

Yes it is an industrial i/o board. That file did load, the light did come on. I need to tell the fpga guys they gave ... Dennis Volper

03:46 PM Software Development: RE: Loading FPGA

If you are using the Industrial I/O board Critical Link provided, try using the file attached below. This file is kn... Michael Williamson

03:35 PM Software Development: RE: Loading FPGA

Sorry about the typo-s. My email/web machine doesn't have a serial port so I've got an old laptop running the hyperte... Dennis Volper

03:16 PM Software Development: RE: Loading FPGA

On the tftp, what is the reported size of the transfer? Something like 0x71544 is expected. If the data is not the ri... John Pruitt

03:08 PM Software Development: RE: Loading FPGA

I did tftp: 0xC0700000 192.168.1.118:fpga.bin
got the ### marks
Did
loadfpga 0xC07000000
no light, message "... Dennis Volper

02:58 PM Software Development: RE: Loading FPGA

Yes, the "done" LED should light up when the FPGA is programmed correctly.
Can you include the set of commands you... John Pruitt

02:51 PM Software Development: RE: Loading FPGA

Should the "done" LED light up if the FPGA was programmed correctly? Dennis Volper

02:39 PM Software Development: RE: Loading FPGA

Dennis,
You are correct that the write command is missing the offset.
In the setenv command, the read is corre... John Pruitt

02:21 PM Software Development: Loading FPGA

I've tried loading the FPGA. I didn't write the FPGA code, I'm just trying to load an fpga.bin file that I've been gi... Dennis Volper

08/09/2010

08:57 PM Software Development: RE: Kernel documentation

Interrupt number 91 (aka IRQ_DA850_RPIINT) works. It works, when I queue a DMA write I get an interrupt when it is co... Dennis Volper

08:40 PM Software Development: RE: Kernel documentation

The information you are looking for is in the "OMAP-L138 System Reference Guide":http://www.ti.com/litv/pdf/sprugm7d,... Michael Williamson

03:50 PM Software Development: RE: Kernel documentation

Building the uPP driver. I need to register and interrupt service routine.
To do that I need to know the irq number ... Dennis Volper

08/03/2010

01:41 PM Software Development: RE: Debugging DSP side with CCS_3.3

HI Mike,
Here is my about dialog:
!cc3about.png!
When I tried to update to 3.3.82 the installer told me I didn... Rich Bagdazian

01:20 PM Software Development: RE: Debugging DSP side with CCS_3.3

Rich,
I am attaching the CCS version information window from help->about.
!CCSVersionInfo.png!
I just tried ... Michael Williamson

01:08 PM Software Development: RE: Debugging DSP side with CCS_3.3

Hi Mike,
Ok, that doesn't seem to work. I downloaded the update version to install CCS 3.3 v12 and when I ran the up... Rich Bagdazian

08/02/2010

06:39 PM Software Development: RE: Debugging DSP side with CCS_3.3

HI Mike,
I just found out I need to be running release 12 of CCS and I'm on release 11 so I'm going to upgrade and s... Rich Bagdazian

06:14 PM Software Development: RE: Debugging DSP side with CCS_3.3

Are you using the latest version of CCS 3.3?
Can you connect to the DSP while at a u-boot prompt (without the DSPL... Michael Williamson

05:48 PM Software Development: Debugging DSP side with CCS_3.3

Hi Mike,
I got the CCS configuration setup as far as I can tell correctly using the platform configuration file fo... Rich Bagdazian

07/28/2010

09:00 AM Software Development: RE: Kernel documentation

Hi Dennis,
It doesn't look like there is a uPP driver for the linux / ARM side available from TI at the moment. T... Michael Williamson

07/27/2010

07:56 PM Software Development: RE: Kernel documentation

Wading through the kernel I haven't spotted a uPP module, will I need to write a module for that also. Dennis Volper

05:53 PM Software Development: RE: kernel fetch problems

IGNORE PREVIOUS MESSAGE, my fault. One of our servers blew a power supply and I manage to skip the make mightyomap in... Dennis Volper

05:40 PM Software Development: RE: kernel fetch problems

Ran the make's using the existing .config (make menuconfig, make uImage plus environment fluff).
Hit a problem with ... Dennis Volper

05:16 PM Software Development: RE: kernel fetch problems

Got it. Compiling the kernel now. Looks good! Thanks. Dennis Volper

03:59 PM Software Development: RE: kernel fetch problems

I put a gzip'd tarball of the our current linux kernel tree in the files section.
commit 2e70fb60c2ace830e0b7170240a... Tim Iskander

07/26/2010

07:36 PM Software Development: RE: kernel fetch problems

I'm going to need a tgz that I can ftp. We got the clone to "work", to an off-site machine, but the git unpack-object... Dennis Volper