Activity
From 07/03/2011 to 08/01/2011
07/29/2011
- 11:37 AM FPGA Development: RE: Programming the FPGA
- Thanks Mike. I picked up the common VHDL files with no trouble.
However, when I tried to add a netlist file (.ngc?... - 07:30 AM FPGA Development: RE: Programming the FPGA
- Hi Craig,
Yeah, the Xilinx ISE file format really doesn't use relative path names very well.
As far as the VHDL...
07/27/2011
- 05:28 PM Software Development: RE: NAND controller, EDMA3 and EMIFA priorities
- Hi Mads,
I'm not sure there is much more you can do than what is already configured.
You might consider cross p... - Hi
I have a few questions regarding the NAND flash and EMIFA.
From the EDMA priority settings below (which I ju... - 05:05 PM Software Development: RE: Mapping code to IRAM
- Hi Mark
You could try the #pragma CODE_SECTION(<function name>, "mysect") (In C++ you omit the function name and p...
07/26/2011
- 05:14 PM Software Development: RE: Mapping code to IRAM
- Hi Marc -
I'm not sure we will have the answer to this question as it's really a TI question. While we're waiting... - Hey All,
I am using CCS4 and SYS/BIOS to program the DSP core in the L138, and I am trying to figure out how to sp... - 09:43 AM FPGA Development: RE: Programming the FPGA
- I opened this project file in XISE and it yelled at me for a number of VHD files (see attached png).
example.zip -...
07/24/2011
- 08:44 PM FPGA Development: RE: Programming the FPGA
- Success has been achieved. Thanks Mike!
I loaded the stock uImage from the .run file supplied with the kit. That d... - 12:55 PM FPGA Development: RE: Programming the FPGA
- Hi Craig,
I think you need to modify the bootargs assuming the NAND has a valid filesystem on it.
See "this wik... - 09:45 AM FPGA Development: RE: Programming the FPGA
- The uImage_Indio_20110723 kernel image booted but could not mount to a filesystem.
Getting closer!
I attached t...
07/23/2011
- 12:52 PM FPGA Development: RE: Programming the FPGA
- Thanks Mike.
My plan is to also extract the image from the .run file and try both this afternoon.
I am using th... - 11:40 AM FPGA Development: RE: Programming the FPGA
- Hi Craig,
I am attaching a uImage file built for the Industrial I/O board from our kernel code baseline.
This r... - 10:57 AM FPGA Development: RE: Programming the FPGA
- Hey Mike,
Late yesterday I booted into UBOOT; cleared the bootfpga (setenv bootfpga;saveenv); rebooted with Angstr... - 09:04 AM FPGA Development: RE: Programming the FPGA
- Hi Craig,
Just following up. Are you still DOA? Or did not programming the FPGA clear the issue?
-Mike
07/22/2011
- 01:24 PM FPGA Development: RE: Programming the FPGA
- Good point. I'll defer any FPGA programming until I resolve the linux kernel load.
Here's the boot text. You can s... - 01:14 PM FPGA Development: RE: Programming the FPGA
- Also,
Can you dump the entire boot text from power up to hang? Would like to see all the commands executed by the... - 01:13 PM FPGA Development: RE: Programming the FPGA
- Hi Craig,
Are you programming the FPGA before you load the kernel? The FPGA can cause problems with the kernel lo... - 01:06 PM FPGA Development: RE: Programming the FPGA
- I tried again in case I screwed up the first time.
I also tried the uImage file in /boot on another of our boards....
07/21/2011
- 05:00 PM FPGA Development: RE: Programming the FPGA
- Hi Greg,
Thanks for XISE files.
I followed instructions from Linux Kernel installtion using uImage from files a... - 02:03 PM FPGA Development: RE: Programming the FPGA
- Hi Craig,
I've attached the project file used to build the .bin file I posted earlier. You'll need to link against... - 02:02 PM FPGA Development: RE: Programming the FPGA
- The revised read instruction works!
We have the L138-FI-225-RC. My mistake. I was looking at the wrong line in the... - 01:43 PM FPGA Development: RE: Programming the FPGA
- Hi Craig,
For the bootgpga image, you need to read out all of the image into RAM before trying to program the FPGA... - 01:03 PM FPGA Development: RE: Programming the FPGA
- Question on automatically loading the FPGA at boot...
I've followed these instructions:
loadb 0xC0700000
[send... - 12:21 PM FPGA Development: RE: Programming the FPGA
- Can you guys zip up and post or e-mail me source files used to generate this .bin?
I would like to play some with ... - 11:09 AM FPGA Development: RE: Programming the FPGA
- Hi Tim.
I'm on my 3rd USB-to-serial adapter and 4th attempt at driver update. I'm sure some manager got a nice bon... - 10:15 AM FPGA Development: RE: Programming the FPGA
- Hi Tim,
Do I need a different version of SPIWriter_MityDSP-L138.out? Didn't see this file in the latest zip.
I ... - 09:07 AM FPGA Development: RE: Programming the FPGA
- Craig
I have uploaded the latest serial programming utility to the files section.
Try that and see if it corrects ... - 08:22 AM FPGA Development: RE: Programming the FPGA
- I've tried several other usb to serial adaptors with no luck.
I get the same error:
(AIS Parse): Performing Opco...
07/20/2011
- 12:10 PM FPGA Development: RE: Programming the FPGA
- Yes. I'm using USB to serial dongle. It's unbranded using Prolific chipset. Unfortunately I do not have a "real" seri...
- 10:43 AM FPGA Development: RE: Programming the FPGA
- Craig
I see your serial port is COM7.. I presume that is a USB serial dongle? What brand / model is it? We have had ... - 10:25 AM FPGA Development: RE: Programming the FPGA
- Tried dead board instructions (sfh_OMAP-L138 -flash -v -p COM7 UBL_SPI_MEM.ais u-boot.bin) and I get read error:
(... - 09:01 AM FPGA Development: RE: Programming the FPGA
- Craig
If you set the bootfpga environment var, uboot will automatically run the commands at startup. I'm not exactly... - 08:57 AM FPGA Development: RE: Programming the FPGA
- Good news / bad news.
It was a successful load. Green DONE led lit.
However, I apparently hammered the flash wi...
07/19/2011
- 05:06 PM FPGA Development: RE: Programming the FPGA
- Hi Craig,
I've attached a .bin file that should work for you (in the future we will add LX45 example .bin files to... - 02:49 PM FPGA Development: RE: Programming the FPGA
- Hi Greg.
This command worked: U-Boot > sf erase 0x580000 0x170000
But you are right. I still have issues.
I ... - 01:50 PM FPGA Development: RE: Programming the FPGA
- Hi Craig,
The flash erase needs to be page aligned. This should work:... - 01:22 PM FPGA Development: RE: Programming the FPGA
- Tim - I think we are getting close.
Here's the result:
U-Boot > sf erase 0x580000 0x16b000
SPI flash erase failed - 12:53 PM FPGA Development: RE: Programming the FPGA
- Craig
Aha!
The default size for uboot's loadfpga command (and what is shown on the wiki!) is 0x80000 (1/2MB), whic... - 11:49 AM FPGA Development: RE: Programming the FPGA
- Thanks Tim.
No DONE led yet but looks as if I made progress:
U-Boot > sf probe 0; sf read 0xc0700000 0x580000 ... - 11:43 AM FPGA Development: RE: Programming the FPGA
- Craig,
another thing to check is that the configuration of the device is correct.
if you run factoryconfig at the U... - 11:32 AM FPGA Development: RE: Programming the FPGA
- Craig
The DONE led should go on immediately after programming the FPGA.
Can you try running the commands in the boo... - I'm following these Wiki instructions and I'm not getting the DONE led:
U-Boot > loadb 0xC0700000
## Ready for bi...
07/15/2011
- 11:18 AM Software Development: RE: MityDSPl138 JTAG
- Marc,
Try stopping the ARM in the u-Boot phase and see if you can connect to the DSP then. The linux portion of A... - Hey All,
I have the XDS100V1 JTAG emulator, and I'm trying to connect to the DSP core with CCS4, but it does not s... - 07:17 AM Software Development: RE: MITYDSP OMAP-L138 EMIF FPGA / NAND shared bus access
- Hi Mike
I have a few questions regarding the NAND flash and EMIFA.
As you earlier mentioned I could try adjusti...
07/14/2011
- 02:03 PM Software Development: RE: uPP/DMA registers
- You will definitely need to configure the pin mux. You should assume that the UPP is powered down (in the reset stat...
- 01:58 PM Software Development: RE: uPP/DMA registers
- Mike,
Thanks for the link to the OMAP specification. I think that is all I needed to start work on my driver. I... - 01:13 PM Software Development: RE: uPP/DMA registers
- Hi Scott,
Unfortunately, TI (nor Critical Link) provides linux drivers for the UPP.
The memory map that include... - Hello,
I want to use the uPP and EMIFA to pass data between an FPGA and the ARM on the OMAP. I think I've got wha...
07/13/2011
- 03:17 PM Software Development: RE: Default Clock Speed
- No, it won't change the clocks. It will just feed the RTOS the correct numbers.
You really should set the frequen... - 02:55 PM Software Development: RE: Default Clock Speed
- Will GBL_setFrequency(); actually change the clock, or just feed the RTOS will correct numbers like you were talking ...
- 02:49 PM Software Development: RE: Default Clock Speed
- Hi,
I want to clarify a couple of things here.
The DSP and the ARM clocks are driven by the same system clock. ... - 02:07 PM Software Development: RE: Default Clock Speed
- Hi Marc,
The boards default to running at 300 MHz, though they can be run at 456 MHz. You can change this in the D... - Hey All,
What speed will an out of the box MityDSP-L138 run at? I was under the assumption it was 456MHz, but whe...
07/06/2011
- 05:13 PM Software Development: RE: core/regs_gpio.h
- Hello Mads,
Thanks for the heads up on the GpioRegs structure. You are right, that is indeed an error in the file... - Hi
I had some trouble getting GPIO working correctly in the OMAP.
Until I found out that the below structure is ... - Dear Sir,
I am looking for an evaluation board that supports real-time embedded linux.
I found that MityDSP-L138 ...
07/05/2011
- 02:23 AM Software Development: RE: MITYDSP OMAP-L138 EMIF FPGA / NAND shared bus access
- Hi Mike
Many thanks for your reply.
It is really latency we are worried about. We won't be transferring a lot o...
07/04/2011
- 03:03 PM Software Development: RE: MITYDSP OMAP-L138 EMIF FPGA / NAND shared bus access
- Hi Mads,
NAND does share the EMIF bus with the FPGA and you may run into a potential latency issue if you do not m... - Hi
This is NOT a problem we are seeing (yet?), but we are wondering whether this is a problem we might be seeing i... - 10:32 AM Software Development: RE: HelloWorldARM DSPLINK example causes Assertion failed
- Hi Greg
Sorry I haven't replied yet.
Has been busy on other tasks, and this was a low low priority :-)
I have ...
07/03/2011
- 01:36 PM Software Development: RE: mtdblock kernel crash
- Oh, if you need an /dev/mtdx device, you need to enable in the kernel:
CONFIG_MTD_CHAR
Should be in the device ... - 01:31 PM Software Development: RE: mtdblock kernel crash
- Hi Zoltan,
Well, for the SPI issue, I have some information for you along with couple of work-arounds. Feel free ...
Also available in: Atom
Go to top
