Project

General

Profile

Activity

From 03/30/2013 to 04/28/2013

04/23/2013

01:55 PM FPGA Development: RE: OFFSET constraint never passes timing
Hi,
Two things.
1) You don't need the OFFSET=OUT spec with our IP. It turns out there is an extra clock in the...
Michael Williamson
01:38 PM Software Development: RE: SATA mount point
You can also run "udevadm monitor" to watch for udev activity.
Tim Iskander
01:29 PM Software Development: RE: SATA mount point
Scott,
I'm not sure whats going on. I can't explain why one would work as expected and the other doesn't. Its po...
Jonathan Cormier
11:44 AM Software Development: RE: SATA mount point
the mmc card does not affect the mounting. It behaves the same way with or without it. I don't know if there are an... Scott Whitney
11:39 AM Software Development: RE: SATA mount point
Just as a curiousity, have you tried to see if adding/removing the mmc card affects how the sata drive mounts. Its t... Jonathan Cormier
11:35 AM Software Development: RE: SATA mount point
i am uploading 4 files both my /etc/fstab and the output of fdisk. This is from 2 different systems with different S... Scott Whitney
11:24 AM Software Development: RE: SATA mount point
Scott,
Could you attach your fstab for both machines as well as the output of 'fdisk -l'?
-Jonathan
Jonathan Cormier
11:07 AM Software Development: SATA mount point
_Hello,
I've got a few mityDSP developement kits and am attaching SATA SSD drives to them. They are formated EXT4 w...
Scott Whitney

04/22/2013

02:11 PM FPGA Development: OFFSET constraint never passes timing
I am using the following timing constraints.
If I remember correctly, I started from the industrial I/O example and ...
Emmett Bradford

04/17/2013

06:31 PM Software Development: RE: USB on the go speed
Hi Mike,
It would be great if I can get a copy of your sample code! It would help tremendously if I can get close to...
Lars Majlof
05:03 PM Software Development: RE: USB on the go speed
Hi Lars,
We have found that RNDIS has been very slow as well and we have not used the serial gadget, but I would s...
Michael Williamson
04:20 PM Software Development: USB on the go speed
Hi,
When I configure Linux (3.2.0+) to use the ethernet gadget with RNDIS support, I get poor data transfer speeds. ...
Lars Majlof

04/15/2013

08:54 PM Software Development: RE: release_2012-03-12.run install failed
Check the "BSP Wiki Page":http://support.criticallink.com/redmine/projects/arm9-platforms/wiki/Board_Support_Package.... Michael Williamson
08:46 PM Software Development: release_2012-03-12.run install failed
Hello all,
I was failed when i tried to install release_2012-03-12.run,
my OS is Ubuntu 12.04,
it prints in the te...
yilin wang
11:15 AM Software Development: RE: SATA not recognized
Mary,
Thanks for the update. I have created a task to enable SATA by default for the next MDK release. It was set...
Jonathan Cormier
09:24 AM Software Development: RE: SATA not recognized
I got it working.
I compared myconfig to the .config file in the MDK_2012-08-10 linux-davinci directory and they w...
Mary Frantz

04/11/2013

01:57 PM Software Development: RE: SATA not recognized
I don't think you will need to rebuild DSPLINK or CMEM.
You should be able to take the myconfig and copy it to the...
Michael Williamson
01:36 PM Software Development: RE: SATA not recognized
What's the best way to do that and change only that one feature?
I generated a config file from my kernel with the...
Mary Frantz
11:54 AM Software Development: RE: SATA not recognized
You need SATA_AHCI_PLATFORM set. You will need to rebuild the kernel.
-Mike
Michael Williamson
11:42 AM Software Development: RE: SATA not recognized
Here's the result:... Mary Frantz
11:36 AM Software Development: RE: SATA not recognized
Mary,
You can print the kernel config file by running:
_zcat /proc/config.gz _
You can then search the outpu...
Jonathan Cormier
11:24 AM Software Development: RE: SATA not recognized
My colleague has another SATA drive and MityDSP board. He reports as follows:
"The drive comes up fine in Windows...
Mary Frantz
10:51 AM Software Development: RE: SATA not recognized
Mary,
There should be no reason that the drive isn't detected by Windows XP when using a USB to Sata adapter. Ass...
Jonathan Cormier
09:20 AM Software Development: RE: SATA not recognized
I have tried the same SATA drive on a second MityDSP board as well as an older SATA drive. There are no "ata" messag... Mary Frantz

04/10/2013

09:50 PM Software Development: Open Embedded build error
Hi,
I've followed the instructions on http://support.criticallink.com/redmine/projects/arm9-platforms/wiki/Install...
Joel Seidman

04/09/2013

02:02 PM Software Development: RE: GPIO interrupt in MityOMAP-L138F
Hi Mike,
thanks for fast reply!
The best would be an example using an fpga gpio pin and an omap pin, just to tes...
Michele Canepa

04/08/2013

01:07 PM Software Development: RE: GPIO interrupt in MityOMAP-L138F
Are you trying to use a FPGA GPIO or an OMAP-L138 GPIO?
The DspGpio.h class should provide access to the OMAP-L138...
Michael Williamson
11:36 AM Software Development: GPIO interrupt in MityOMAP-L138F
Hello all,
I need to hook a HWI to a GPIO pin in a DSP application.
I have some questions:
1- Do your core libra...
Michele Canepa
12:49 PM Software Development: RE: L138 - DSP Timer interrupt question ...
Mike,
Thanks for information. Always very intressting. I am reading the Day2_AM training document.
Here our cu...
François Tremblay
12:58 AM Software Development: Start Guide : Cannot build helloworld application with eclipse
Hello,
I am using Virtual Box and MityDSP-L138_SDK_2012_06_13.eva image.
When I following Start Guide instruction ...
minh tung

04/07/2013

07:53 AM Software Development: RE: L138 - DSP Timer interrupt question ...
Check the "Interrupt Handling - Delayed Branch Latency" section of the Day2_AM training presentation located in our "... Michael Williamson

04/04/2013

04:27 PM Software Development: RE: L138 - DSP Timer interrupt question ...
Mike,
Can you add more details regarding this statement: _The DSP loop optimization can create large interrupt lat...
François Tremblay
11:43 AM Software Development: RE: MityDSP-L138F Failure to Boot and Cannot Reset
Also feel free to look through the wiki http://support.criticallink.com/redmine/projects/arm9-platforms/wiki Jonathan Cormier
11:40 AM Software Development: RE: MityDSP-L138F Failure to Boot and Cannot Reset
The username for the modules should be _root_
Jonathan Cormier

04/03/2013

10:16 PM Software Development: RE: MityDSP-L138F Failure to Boot and Cannot Reset
Hi,
Thank you so much for supporting.
For (1): At the first time. Now the board are running with null modem cable...
minh tung
07:17 AM Software Development: RE: MityDSP-L138F Failure to Boot and Cannot Reset
I am assuming these are out of the box Development kits?
For (1) the console UART, please ensure you are using the...
Michael Williamson
08:27 AM PCB Development: RE: Resistors in EMA signal and adress traces?
Mike,
it's the L138-FX-225-RC Module. No FPGA.
I'm concerned about both kinds of traces.
Christian
Christian Rückl
07:33 AM PCB Development: RE: Resistors in EMA signal and adress traces?
Which part number? Specifically, does the module include an FPGA or not?
Which EMA traces are you concerned with,...
Michael Williamson
07:30 AM PCB Development: Resistors in EMA signal and adress traces?
Hi,
can anybody tell me if there are already resistors on the EMA-traces on the L138-Modul integrated? If yes, wha...
Christian Rückl

04/02/2013

10:36 PM Software Development: MityDSP-L138F Failure to Boot and Cannot Reset
Hello
I am using Industrial I/O board(80-000268RI-2 A) and 2 L138 board (L138-CG-225-RC ,L138-FG-225-RC).I got 2 i...
minh tung
 

Also available in: Atom

Go to top
Add picture from clipboard (Maximum size: 1 GB)