Activity

From 12/28/2017 to 01/26/2018

09:24 PM Software Development: RE: SYS/BIOS: Finally i could solve this issue by adding the following code :
asm(" mrc p15, #0, r0, c1, c0, #0\n\t"
" orr r0, ... Martin Hantke

07:47 PM Software Development: RE: Auto run of application file (loaded in NAND Flash): Vivek Ponnani wrote:
> Jonathan Cormier wrote:
> > Vivek Ponnani wrote:
> > > Thanks for your response. It is very... Jonathan Cormier
05:13 PM Software Development: RE: Auto run of application file (loaded in NAND Flash): Jonathan Cormier wrote:
> Vivek Ponnani wrote:
> > Thanks for your response. It is very helpful.
> >
> > Most of... Vivek Ponnani
03:59 PM Software Development: RE: Auto run of application file (loaded in NAND Flash): Vivek Ponnani wrote:
> Thanks for your response. It is very helpful.
>
> Most of the points are cleared. I have f... Jonathan Cormier
02:24 PM Software Development: RE: Auto run of application file (loaded in NAND Flash): Thanks for your response. It is very helpful.
Most of the points are cleared. I have further queries as below.
... Vivek Ponnani

02:51 PM Software Development: RE: Auto run of application file (loaded in NAND Flash): Vivek Ponnani wrote:
> Hi,
>
> I have a custom board with
> -- MityDspl-138F module (with FPGA)
> -- No Ethern... Jonathan Cormier
11:23 AM Software Development: Auto run of application file (loaded in NAND Flash): Hi,
I have a custom board with
-- MityDspl-138F module (with FPGA)
-- No Ethernet port
-- UART,USB,SD CARD int... Vivek Ponnani
01:57 PM Software Development: SYS/BIOS: Hello Forum,
i have a question related to usage of TI SYS/Bios on MiTyDSP without FPGA.
i successsfull flashed my a... Martin Hantke

11:51 AM Software Development: RE: uPP on MityDsp: Hello Greg,
many thanks for your answers.
I will try that configuration, takes a while.
Great Support Many Thank... Martin Hantke

06:06 PM Software Development: RE: uPP on MityDsp: Hi Martin,
LCD [8] - LCD [15] also function as Boot Mode Selection pins. The SN54LVC157A is used to change the pu... Gregory Gluszek
04:27 PM Software Development: RE: uPP on MityDsp: Hello Greg,
many thanks for your answer.
as i Know LCD[x] pins are outputs. and on the MityDsp is see U9 which is a... Martin Hantke
04:05 PM Software Development: RE: uPP on MityDsp: Hi Martin,
I have never personally used the uPP in this setup, however, it looks like it should be possible.
... Gregory Gluszek
02:24 PM Software Development: uPP on MityDsp: I have a question for clarification.
We want to use MityDsp without FPGA and use both uPP-Channels as Input.
Is tha... Martin Hantke

03:18 PM Software Development: RE: IPC and uPP interrupts APIs conflict: Hi Okan,
I'm not too familiar with either syslink or starterware. However I've found that when I'm debugging kerne... Jonathan Cormier
12:42 PM Software Development: RE: IPC and uPP interrupts APIs conflict: Hi Greg,
I've already read the relevant sections of the technical reference manual and megamodule reference guide,... Okan Çalış

04:03 PM Software Development: RE: IPC and uPP interrupts APIs conflict: Hi Okan,
My guess is that your core problem is that SysLink and StarterWare simply do not play well together in g... Gregory Gluszek
05:51 AM Software Development: RE: IPC and uPP interrupts APIs conflict: Hello again,
I've just realized the line "@ISTP = (unsigned int)_intcVectorTable;@" in @{StarterWare}/system_confi... Okan Çalış

02:07 PM Software Development: RE: Linux USB Gadget is not working on custom board: Glad it worked. I suspect your ID pin is being pulled low somehow. But as long as you don't need to support HOST mo... Jonathan Cormier
10:23 AM Software Development: RE: Linux USB Gadget is not working on custom board: Jonathan Cormier wrote:
> In the 3.2 branch Peripheral mode can be configured in the baseboard.
That actually w... Okan Çalış

02:13 PM Software Development: RE: Linux USB Gadget is not working on custom board: Okan Çalış wrote:
> Michael Williamson wrote:
>
> > Do you see these lines even if you don't connect the PC? (I ... Jonathan Cormier
08:47 AM Software Development: RE: Linux USB Gadget is not working on custom board: Michael Williamson wrote:
> Do you see these lines even if you don't connect the PC? (I was looking to see if the... Okan Çalış

02:37 PM Software Development: RE: Linux USB Gadget is not working on custom board: Could you attach your .config?
By default, CONFIG_USB_MUSB_OTG is selected which puts the kernel in OTG mode. In ... Jonathan Cormier
01:27 PM Software Development: RE: Linux USB Gadget is not working on custom board: > Do you see these lines even if you don't connect the PC?
Yes, I see those lines even when not connected to the h... Okan Çalış
01:06 PM Software Development: RE: Linux USB Gadget is not working on custom board: So if you are trying to run in peripheral mode, I am not entirely sure I understand the last lines of your log file:
... Michael Williamson
12:45 PM Software Development: RE: Linux USB Gadget is not working on custom board: Hi Mike,
> Are you using USB as OTG? Host or peripheral mode for your test?
In our tests, the device acts as t... Okan Çalış
12:13 PM Software Development: RE: Linux USB Gadget is not working on custom board: Are you using USB as OTG? Host or peripheral mode for your test?
If you do a dmesg (before and after plugging in ... Michael Williamson
11:37 AM Software Development: Linux USB Gadget is not working on custom board: Hi,
We've been working on a MityDsp-L138F SoM and so far managed to use USB GadgetFS feature of the Linux kernel t... Okan Çalış

01:37 PM Software Development: IPC and uPP interrupts APIs conflict: Hi,
We've been working on a MityDsp-L138F. The ARM and DSP cores run Linux and SYS/BIOS, respectively. We're using... Okan Çalış

02:06 PM Software Development: Real time signal input and output with uPP interface in MityDSP: Hi,
I have a custom board with
1) MityDspl-138F module (with FPGA)
2) No Ethernet port
3) UART,USB,SD CARD int... Vivek Ponnani

Also available in: Atom

Go to top

Mity CPU Platforms » MityDSP-L138 (ARM9 Based Platforms)