Mity CPU Platforms » MityDSP-L138 (ARM9 Based Platforms)

02/01/2018

09:59 PM Software Development: RE: Using McASP Rx clock generation module

Hi Mike, thanks for responding.
So I have updated the baseboard-industrialio.c to enable all of the baseboard_mca... Tom Riddle

09:32 PM Software Development: RE: Using McASP Rx clock generation module

Hi Tom,
Have you checked the pinmux settings for the IO Pin are set to use the McASP function and not GPIO or some... Michael Williamson

09:24 PM Software Development: RE: Using McASP Rx clock generation module

Hi,
We are working thru enabling of the McASP Rx clock generator module. After making source updates to davinci_m... Tom Riddle

01/31/2018

02:42 PM FPGA Development: RE: FPGA Done led not turning on with CPU programming

How are you generating the bin file?
Check this "wiki page":https://support.criticallink.com/redmine/projects/arm9... Michael Williamson

02:04 PM FPGA Development: FPGA Done led not turning on with CPU programming

Hi,
We have made our own customized board uing the Industrial IO Board and the Analog expansion board.
We were pr... Vivek Ponnani

01/30/2018

07:01 PM Software Development: RE: Auto run of application file (loaded in NAND Flash)

Vivek Ponnani wrote:
>
> 1)When application runs,there is some debug part (as above)which dsp sends to arm with ds... Jonathan Cormier

06:13 PM Software Development: RE: Auto run of application file (loaded in NAND Flash)

I was expecting following Debug response, which comes up when I run application by myself with the help of treaterm a... Vivek Ponnani

03:16 PM Software Development: RE: Auto run of application file (loaded in NAND Flash)

Vivek Ponnani wrote:
> > > 2) FPGA write in SPI Flash
> > > U-Boot > setenv bootcmd "run programfpga"
> > You appe... Jonathan Cormier

02:48 PM Software Development: RE: Auto run of application file (loaded in NAND Flash)

Jonathan Cormier wrote:
> Vivek Ponnani wrote:
> > I followed the suggestions and tried to boot from flash. But It ... Vivek Ponnani

01/29/2018

04:44 PM Software Development: RE: Auto run of application file (loaded in NAND Flash)

Vivek Ponnani wrote:
> I followed the suggestions and tried to boot from flash. But It still does not run applicatio... Jonathan Cormier

03:25 PM Software Development: RE: Auto run of application file (loaded in NAND Flash)

I followed the suggestions and tried to boot from flash. But It still does not run application automatically. Below i... Vivek Ponnani

03:11 AM Software Development: Using McASP Rx clock generation module

Hi,
We are developing a new codec using the MityDSP. So the Industrial IO has the DSD1791 audio DAC on it's McASP.... Tom Riddle

01/25/2018

09:24 PM Software Development: RE: SYS/BIOS

Finally i could solve this issue by adding the following code :
asm(" mrc p15, #0, r0, c1, c0, #0\n\t"
" orr r0, ... Martin Hantke

01/24/2018

07:47 PM Software Development: RE: Auto run of application file (loaded in NAND Flash)

Vivek Ponnani wrote:
> Jonathan Cormier wrote:
> > Vivek Ponnani wrote:
> > > Thanks for your response. It is very... Jonathan Cormier

05:13 PM Software Development: RE: Auto run of application file (loaded in NAND Flash)

Jonathan Cormier wrote:
> Vivek Ponnani wrote:
> > Thanks for your response. It is very helpful.
> >
> > Most of... Vivek Ponnani

03:59 PM Software Development: RE: Auto run of application file (loaded in NAND Flash)

Vivek Ponnani wrote:
> Thanks for your response. It is very helpful.
>
> Most of the points are cleared. I have f... Jonathan Cormier

02:24 PM Software Development: RE: Auto run of application file (loaded in NAND Flash)

Thanks for your response. It is very helpful.
Most of the points are cleared. I have further queries as below.
... Vivek Ponnani

01/23/2018

02:51 PM Software Development: RE: Auto run of application file (loaded in NAND Flash)

Vivek Ponnani wrote:
> Hi,
>
> I have a custom board with
> -- MityDspl-138F module (with FPGA)
> -- No Ethern... Jonathan Cormier

11:23 AM Software Development: Auto run of application file (loaded in NAND Flash)

Hi,
I have a custom board with
-- MityDspl-138F module (with FPGA)
-- No Ethernet port
-- UART,USB,SD CARD int... Vivek Ponnani

01:57 PM Software Development: SYS/BIOS

Hello Forum,
i have a question related to usage of TI SYS/Bios on MiTyDSP without FPGA.
i successsfull flashed my a... Martin Hantke

01/18/2018

11:51 AM Software Development: RE: uPP on MityDsp

Hello Greg,
many thanks for your answers.
I will try that configuration, takes a while.
Great Support Many Thank... Martin Hantke

01/17/2018

06:06 PM Software Development: RE: uPP on MityDsp

Hi Martin,
LCD [8] - LCD [15] also function as Boot Mode Selection pins. The SN54LVC157A is used to change the pu... Gregory Gluszek

04:27 PM Software Development: RE: uPP on MityDsp

Hello Greg,
many thanks for your answer.
as i Know LCD[x] pins are outputs. and on the MityDsp is see U9 which is a... Martin Hantke

04:05 PM Software Development: RE: uPP on MityDsp

Hi Martin,
I have never personally used the uPP in this setup, however, it looks like it should be possible.
... Gregory Gluszek

02:24 PM Software Development: uPP on MityDsp

I have a question for clarification.
We want to use MityDsp without FPGA and use both uPP-Channels as Input.
Is tha... Martin Hantke

01/16/2018

03:18 PM Software Development: RE: IPC and uPP interrupts APIs conflict

Hi Okan,
I'm not too familiar with either syslink or starterware. However I've found that when I'm debugging kerne... Jonathan Cormier

12:42 PM Software Development: RE: IPC and uPP interrupts APIs conflict

Hi Greg,
I've already read the relevant sections of the technical reference manual and megamodule reference guide,... Okan Çalış

01/15/2018

04:03 PM Software Development: RE: IPC and uPP interrupts APIs conflict

Hi Okan,
My guess is that your core problem is that SysLink and StarterWare simply do not play well together in g... Gregory Gluszek

05:51 AM Software Development: RE: IPC and uPP interrupts APIs conflict

Hello again,
I've just realized the line "@ISTP = (unsigned int)_intcVectorTable;@" in @{StarterWare}/system_confi... Okan Çalış

01/12/2018

02:07 PM Software Development: RE: Linux USB Gadget is not working on custom board

Glad it worked. I suspect your ID pin is being pulled low somehow. But as long as you don't need to support HOST mo... Jonathan Cormier

10:23 AM Software Development: RE: Linux USB Gadget is not working on custom board

Jonathan Cormier wrote:
> In the 3.2 branch Peripheral mode can be configured in the baseboard.
That actually w... Okan Çalış

01/11/2018

02:13 PM Software Development: RE: Linux USB Gadget is not working on custom board

Okan Çalış wrote:
> Michael Williamson wrote:
>
> > Do you see these lines even if you don't connect the PC? (I ... Jonathan Cormier

08:47 AM Software Development: RE: Linux USB Gadget is not working on custom board

Michael Williamson wrote:
> Do you see these lines even if you don't connect the PC? (I was looking to see if the... Okan Çalış

01/10/2018

02:37 PM Software Development: RE: Linux USB Gadget is not working on custom board

Could you attach your .config?
By default, CONFIG_USB_MUSB_OTG is selected which puts the kernel in OTG mode. In ... Jonathan Cormier

01:27 PM Software Development: RE: Linux USB Gadget is not working on custom board

> Do you see these lines even if you don't connect the PC?
Yes, I see those lines even when not connected to the h... Okan Çalış

01:06 PM Software Development: RE: Linux USB Gadget is not working on custom board

So if you are trying to run in peripheral mode, I am not entirely sure I understand the last lines of your log file:
... Michael Williamson

12:45 PM Software Development: RE: Linux USB Gadget is not working on custom board

Hi Mike,
> Are you using USB as OTG? Host or peripheral mode for your test?
In our tests, the device acts as t... Okan Çalış

12:13 PM Software Development: RE: Linux USB Gadget is not working on custom board

Are you using USB as OTG? Host or peripheral mode for your test?
If you do a dmesg (before and after plugging in ... Michael Williamson

11:37 AM Software Development: Linux USB Gadget is not working on custom board

Hi,
We've been working on a MityDsp-L138F SoM and so far managed to use USB GadgetFS feature of the Linux kernel t... Okan Çalış

01/09/2018

01:37 PM Software Development: IPC and uPP interrupts APIs conflict

Hi,
We've been working on a MityDsp-L138F. The ARM and DSP cores run Linux and SYS/BIOS, respectively. We're using... Okan Çalış

01/04/2018

02:06 PM Software Development: Real time signal input and output with uPP interface in MityDSP

Hi,
I have a custom board with
1) MityDspl-138F module (with FPGA)
2) No Ethernet port
3) UART,USB,SD CARD int... Vivek Ponnani