Activity

From 01/30/2018 to 02/28/2018

03:12 PM Software Development: RE: Kernel panics on custom board: "No init found. Try passing init= option to kernel": Okan Çalış wrote:
> Hi Jonathan, thanks for your reply.
>
> > The kernel and u-boot both have to use the same ECC... Jonathan Cormier
12:07 PM Software Development: RE: Kernel panics on custom board: "No init found. Try passing init= option to kernel": Hi Jonathan, thanks for your reply.
> The kernel and u-boot both have to use the same ECC strength.
I'm afraid ... Okan Çalış

02:14 PM Software Development: RE: Kernel panics on custom board: "No init found. Try passing init= option to kernel": Okan Çalış wrote:
> Hi,
>
> I couldn't reply sooner because I've been handling some other kernel-related problems... Jonathan Cormier
07:38 AM Software Development: RE: Kernel panics on custom board: "No init found. Try passing init= option to kernel": Hi,
I couldn't reply sooner because I've been handling some other kernel-related problems by using NFS as a tempor... Okan Çalış

02:04 AM PCB Development: getting AUDIO_SYSCLK to expansion connector: I have an Industrial I/O board and need to get the AUDIO_SYSCLK signal out to an expansion board connector. Currently... Tom Riddle

02:17 PM Software Development: RE: Kernel panics on custom board: "No init found. Try passing init= option to kernel": > U-Boot > print ver
> ver=U-Boot 2017.05-rc1-00044-gc3b7cfe-dirty (Apr 08 2017 - 20:35:07 +0300)
This is definitel... Jonathan Cormier
12:26 PM Software Development: RE: Kernel panics on custom board: "No init found. Try passing init= option to kernel": Is your custom board using a MityDSP-L138, or have you designed a custom board using the OMAP-L138 and not the module... Michael Williamson
11:56 AM Software Development: RE: Kernel panics on custom board: "No init found. Try passing init= option to kernel": Turns out that the custom board doesn't even have a @factoryconfig@ command. The two boards appear to have different ... Okan Çalış
02:01 PM Software Development: RE: Auto run of application file (loaded in NAND Flash): Vivek Ponnani wrote:
> Currently our application program is part of .jffs2 file system (Linux root file system + ap... Jonathan Cormier

03:08 PM Software Development: RE: Kernel panics on custom board: "No init found. Try passing init= option to kernel": Okan Çalış wrote:
> But this is our custom board. What should I enter in those fields?
This is the factory config... Jonathan Cormier
02:57 PM Software Development: RE: Kernel panics on custom board: "No init found. Try passing init= option to kernel": But this is our custom board. What should I enter in those fields? Okan Çalış
02:38 PM Software Development: RE: Kernel panics on custom board: "No init found. Try passing init= option to kernel": > MityOMAPL138: Read Factory Config Failed: -110
This line is very concerning. It appears you have erased or corrup... Jonathan Cormier
05:58 AM Software Development: RE: Kernel panics on custom board: "No init found. Try passing init= option to kernel": Hi Jonathan,
> Your u-boot and kernel partitions don't seem to match.
I changed the file @board-mityomapl138.c... Okan Çalış
10:14 AM FPGA Development: RE: FPGA Done led not turning on with CPU programming: Michael Williamson wrote:
> How are you generating the bin file?
>
> Check this "wiki page":https://support.criti... Vivek Ponnani
10:11 AM Software Development: RE: Auto run of application file (loaded in NAND Flash): Jonathan Cormier wrote:
> Vivek Ponnani wrote:
> >
> > 1)When application runs,there is some debug part (as above... Vivek Ponnani

04:31 PM Software Development: RE: Using McASP Rx clock generation module: Ideally you should get it working from the baseboard as that should be the source of all the pinmux settings. Not su... Jonathan Cormier
04:12 PM Software Development: RE: Using McASP Rx clock generation module: Hi Jonathan,
Ok, good suggestion... thanks... the pinmux read
PINMUX0 = 0x8811.1110
so it's not getting set... Tom Riddle
02:40 PM Software Development: RE: Kernel panics on custom board: "No init found. Try passing init= option to kernel": Your u-boot and kernel partitions don't seem to match. Also asuming the u-boot partitions scheme is the correct one, ... Jonathan Cormier
05:08 AM Software Development: Kernel panics on custom board: "No init found. Try passing init= option to kernel": Hi,
As some of you may know, I've been working on a MityDsp-L138F SoM, and I also have a custom designed board bas... Okan Çalış

06:57 PM Software Development: RE: Using McASP Rx clock generation module: Can you dump the pinmux registers so we can double check them?
0x01C14120 - PINMUX0
0x01C14124 - PINMUX1 Jonathan Cormier

09:59 PM Software Development: RE: Using McASP Rx clock generation module: Hi Mike, thanks for responding.
So I have updated the baseboard-industrialio.c to enable all of the baseboard_mca... Tom Riddle
09:32 PM Software Development: RE: Using McASP Rx clock generation module: Hi Tom,
Have you checked the pinmux settings for the IO Pin are set to use the McASP function and not GPIO or some... Michael Williamson
09:24 PM Software Development: RE: Using McASP Rx clock generation module: Hi,
We are working thru enabling of the McASP Rx clock generator module. After making source updates to davinci_m... Tom Riddle

02:42 PM FPGA Development: RE: FPGA Done led not turning on with CPU programming: How are you generating the bin file?
Check this "wiki page":https://support.criticallink.com/redmine/projects/arm9... Michael Williamson
02:04 PM FPGA Development: FPGA Done led not turning on with CPU programming: Hi,
We have made our own customized board uing the Industrial IO Board and the Analog expansion board.
We were pr... Vivek Ponnani

07:01 PM Software Development: RE: Auto run of application file (loaded in NAND Flash): Vivek Ponnani wrote:
>
> 1)When application runs,there is some debug part (as above)which dsp sends to arm with ds... Jonathan Cormier
06:13 PM Software Development: RE: Auto run of application file (loaded in NAND Flash): I was expecting following Debug response, which comes up when I run application by myself with the help of treaterm a... Vivek Ponnani
03:16 PM Software Development: RE: Auto run of application file (loaded in NAND Flash): Vivek Ponnani wrote:
> > > 2) FPGA write in SPI Flash
> > > U-Boot > setenv bootcmd "run programfpga"
> > You appe... Jonathan Cormier
02:48 PM Software Development: RE: Auto run of application file (loaded in NAND Flash): Jonathan Cormier wrote:
> Vivek Ponnani wrote:
> > I followed the suggestions and tried to boot from flash. But It ... Vivek Ponnani

Also available in: Atom

Go to top

Mity CPU Platforms » MityDSP-L138 (ARM9 Based Platforms)