Project

General

Profile

Activity

From 08/02/2012 to 08/31/2012

08/29/2012

10:48 AM Software Development: Booting StarterWare on MityARM-335x
(posted on behalf of a customer)
We would like to use a simple TI StarterWare based design possibly with SYSBIOS....
Thomas Catalino

08/28/2012

01:29 PM PCB Development: RE: MityARM-335x I2C1_SDA and I2C1_SCL Pull-up Resistors
Hi Mike,
Thanks for clarifying how the I2C buses are implemented on the module.
There is no problem, I was uncl...
Joel Minski
10:25 AM Software Development: RE: Boot from NAND?
The MityARM-3359 is capable of booting from NAND. See wiki page http://support.criticallink.com/redmine/projects/armc... Tim Iskander
10:19 AM Software Development: Boot from NAND?
(posted for a customer)
Can the MityARM-3359 boot from NAND?
Thomas Catalino

08/27/2012

07:28 PM PCB Development: RE: MityARM-335x LED D3 GPIO Pin?
The reason you can't talk to the PMIC (from linux) is likely that the pmic driver has grabbed the bus for itself.
If...
Tim Iskander
07:17 PM PCB Development: RE: MityARM-335x LED D3 GPIO Pin?
Hi Mike,
Thanks for the help on where to look. I found the set_led_d3() function inside som.c in u-boot where thi...
Joel Minski
06:59 PM PCB Development: RE: MityARM-335x LED D3 GPIO Pin?
On the AM335x, D2 and D3 are connected to the TPS65910. D2 is connected to VDIG1 (VDIG1 output is only used for D2, ... Michael Williamson
06:32 PM PCB Development: MityARM-335x LED D3 GPIO Pin?
Section 3.7 of the "MityARM-335x Carrier Board Design Guide.doc" from January 8, 2012 states that LED D3 is connected... Joel Minski
07:10 PM PCB Development: RE: MityARM-335x I2C1_SDA and I2C1_SCL Pull-up Resistors
I am looking at the schematic for the SOM, and there are 4.7K Ohm resistors on I2C1_SCL and I2C1_SDA to VDDIO (+3.3V)... Michael Williamson
06:51 PM PCB Development: MityARM-335x I2C1_SDA and I2C1_SCL Pull-up Resistors
It appears that the I2C1 pull-up resistors are placed on the DevKit (connected to the +3.3VDVI net) and not on the Mi... Joel Minski
11:54 AM Software Development: RE: Sending/Receiving Raw Ethernet Packets
Actually I do see the vconfig command, but when I try to execute the command, I get the error:
vconfig: can't open...
Richard Joyce
11:34 AM Software Development: RE: Sending/Receiving Raw Ethernet Packets
I am still unable to build the pcap library into my application. Actually, I don't see the pcap libraries under /usr... Richard Joyce
07:32 AM Software Development: RE: Sending/Receiving Raw Ethernet Packets
Richard
The linker error you have looks like the configure was not set up for cross compiling completely (i.e. /usr/...
Tim Iskander

08/24/2012

08:42 AM Software Development: RE: Sending/Receiving Raw Ethernet Packets
I found this thread on the TI E2E site:
http://e2e.ti.com/support/dsp/davinci_digital_media_processors/f/716/p/12863...
Richard Joyce

08/22/2012

02:49 PM Software Development: RE: Sending/Receiving Raw Ethernet Packets
You might try posting to the "TI E2E site":http://e2e.ti.com and seeing if they plan on supporting it, or if that hav... Michael Williamson
02:46 PM Software Development: RE: Sending/Receiving Raw Ethernet Packets
Ah-ha ... I see I was layer too high!
The good news is I think you are correct about promiscuous mode...
The bad ne...
Tim Iskander
02:40 PM Software Development: RE: Sending/Receiving Raw Ethernet Packets
Here would be another good place to look at what I'm trying to accomplish:
http://linux.die.net/man/7/packet
Rich...
Richard Joyce
02:37 PM Software Development: RE: Sending/Receiving Raw Ethernet Packets
I may not be understanding correctly, but the page you sent is talking about IPv4 raw sockets. Using the protocol IP... Richard Joyce
01:11 PM Software Development: RE: Sending/Receiving Raw Ethernet Packets
Have you set the protocol number correctly, both in the packet and on the linux (335x in this case) machine? If the I... Tim Iskander
11:55 AM Software Development: Sending/Receiving Raw Ethernet Packets
I am trying to write a Linux application for my MityArm 335x Dev board to send and receive raw Ethernet packets to/fr... Richard Joyce

08/06/2012

03:13 PM Software Development: RE: Critical Link Kernel integration w/ Angstrom/OpenEmbedded
Mike,
Thanks for the explanation and fast reply as usual. I think you're probably right that the mainline kernel ...
Ali Asgar Sohanghpurwala

08/05/2012

08:27 PM PCB Development: RE: schematic of MityARM-3359
Thank you, Jason. I sent you an e-mail. Tom Thomas Catalino
03:22 AM PCB Development: RE: schematic of MityARM-3359
Hello, Thomas
Could you also send me a copy of your MityARM 335X schematic to me ( PDF version and Altium format),...
jason AK
02:55 PM Software Development: RE: Critical Link Kernel integration w/ Angstrom/OpenEmbedded
Hello Ali,
I've been watching TI and other folks working against the mainline kernel with AM335x, and it looks far...
Michael Williamson

08/02/2012

01:19 PM Software Development: RE: Critical Link Kernel integration w/ Angstrom/OpenEmbedded
Hello Mike,
I've been poking around some more with Angstrom 2012.05 and Qt5 on our Beaglebone development systems....
Ali Asgar Sohanghpurwala
 

Also available in: Atom

Go to top
Add picture from clipboard (Maximum size: 1 GB)