Activity
From 08/20/2012 to 09/18/2012
09/18/2012
- 04:36 PM Software Development: RE: mod_fastcgi.so
- Hi Scott,
Tried that with no luck...
however I was looking through the lighttpd documentation and saw I forgot t... - 02:45 PM Software Development: RE: mod_fastcgi.so
- Try "--host=arm-angstrom-linux-gnueabi" instead....
-Mike
- 02:30 PM Software Development: RE: mod_fastcgi.so
- Scott,
Downloaded from:
http://download.lighttpd.net/lighttpd/releases-1.4.x/
lighttpd-1.4.26.tar.gz 2010-Feb-07... - 12:38 PM Software Development: RE: mod_fastcgi.so
- Randy,
Could you give me a link to where you downloaded the lighttpd source? Also once you downloaded it, can you ... - 09:41 AM Software Development: RE: mod_fastcgi.so
- Hi Mike,
I found out the version of the lighttpd based on one of the included shared libraries.
I have downloaded...
09/17/2012
- 10:57 AM Software Development: RE: mod_fastcgi.so
- Hi Mike,
Should have mentioned Linux and Lighttpd are very new for me.
I had assumed I could just compile the light...
09/15/2012
- 06:36 AM Software Development: RE: mod_fastcgi.so
- So anyway, the mod-fastcgi.so should not require you to rebuild the kernel. You should be able to download it, "conf...
09/14/2012
- 12:54 PM Software Development: RE: mod_fastcgi.so
- What filesystem are you using? You might be able to get it installed using opkg.
-Mike
- Hi,
I'm trying to use fastcgi with the lighttpd web server. I have successfully create a simple example and changed ...
09/07/2012
- 12:29 AM Software Development: RE: Re-assigning the PHY_RESET
- Hi Tim,
Thanks for you quick reply. I managed to swap the PHY_RESET and get the Ethernet working - Brilliant!.
Than...
09/06/2012
- 10:01 AM Software Development: RE: Re-assigning the PHY_RESET
- Keith
The pinmux setup for the PHY reset should be done in u-boot. It is in board/cl/mityarm335x/mux.c in the rgmii2...
09/05/2012
- Hi,
I want to re-assign the PHY_RESET from gpio3_10 to gpio3_4. I can have included gpio3_4 in mux33xx.c but it ap...
08/29/2012
- (posted on behalf of a customer)
We would like to use a simple TI StarterWare based design possibly with SYSBIOS....
08/28/2012
- 01:29 PM PCB Development: RE: MityARM-335x I2C1_SDA and I2C1_SCL Pull-up Resistors
- Hi Mike,
Thanks for clarifying how the I2C buses are implemented on the module.
There is no problem, I was uncl... - 10:25 AM Software Development: RE: Boot from NAND?
- The MityARM-3359 is capable of booting from NAND. See wiki page http://support.criticallink.com/redmine/projects/armc...
- (posted for a customer)
Can the MityARM-3359 boot from NAND?
08/27/2012
- 07:28 PM PCB Development: RE: MityARM-335x LED D3 GPIO Pin?
- The reason you can't talk to the PMIC (from linux) is likely that the pmic driver has grabbed the bus for itself.
If... - 07:17 PM PCB Development: RE: MityARM-335x LED D3 GPIO Pin?
- Hi Mike,
Thanks for the help on where to look. I found the set_led_d3() function inside som.c in u-boot where thi... - 06:59 PM PCB Development: RE: MityARM-335x LED D3 GPIO Pin?
- On the AM335x, D2 and D3 are connected to the TPS65910. D2 is connected to VDIG1 (VDIG1 output is only used for D2, ...
- Section 3.7 of the "MityARM-335x Carrier Board Design Guide.doc" from January 8, 2012 states that LED D3 is connected...
- 07:10 PM PCB Development: RE: MityARM-335x I2C1_SDA and I2C1_SCL Pull-up Resistors
- I am looking at the schematic for the SOM, and there are 4.7K Ohm resistors on I2C1_SCL and I2C1_SDA to VDDIO (+3.3V)...
- It appears that the I2C1 pull-up resistors are placed on the DevKit (connected to the +3.3VDVI net) and not on the Mi...
- 11:54 AM Software Development: RE: Sending/Receiving Raw Ethernet Packets
- Actually I do see the vconfig command, but when I try to execute the command, I get the error:
vconfig: can't open... - 11:34 AM Software Development: RE: Sending/Receiving Raw Ethernet Packets
- I am still unable to build the pcap library into my application. Actually, I don't see the pcap libraries under /usr...
- 07:32 AM Software Development: RE: Sending/Receiving Raw Ethernet Packets
- Richard
The linker error you have looks like the configure was not set up for cross compiling completely (i.e. /usr/...
08/24/2012
- 08:42 AM Software Development: RE: Sending/Receiving Raw Ethernet Packets
- I found this thread on the TI E2E site:
http://e2e.ti.com/support/dsp/davinci_digital_media_processors/f/716/p/12863...
08/22/2012
- 02:49 PM Software Development: RE: Sending/Receiving Raw Ethernet Packets
- You might try posting to the "TI E2E site":http://e2e.ti.com and seeing if they plan on supporting it, or if that hav...
- 02:46 PM Software Development: RE: Sending/Receiving Raw Ethernet Packets
- Ah-ha ... I see I was layer too high!
The good news is I think you are correct about promiscuous mode...
The bad ne... - 02:40 PM Software Development: RE: Sending/Receiving Raw Ethernet Packets
- Here would be another good place to look at what I'm trying to accomplish:
http://linux.die.net/man/7/packet
Rich... - 02:37 PM Software Development: RE: Sending/Receiving Raw Ethernet Packets
- I may not be understanding correctly, but the page you sent is talking about IPv4 raw sockets. Using the protocol IP...
- 01:11 PM Software Development: RE: Sending/Receiving Raw Ethernet Packets
- Have you set the protocol number correctly, both in the packet and on the linux (335x in this case) machine? If the I...
- I am trying to write a Linux application for my MityArm 335x Dev board to send and receive raw Ethernet packets to/fr...
Also available in: Atom
Go to top
