Activity
From 09/03/2012 to 10/02/2012
10/01/2012
- 12:22 PM PCB Development: RE: Caution on MityARM SO-DIMM PCB Footprint
- Mark,
Thank you for pointing out that lack of information. It has now been addressed and the design guide has been... - 07:40 AM PCB Development: RE: Ethernet PHYs
- Hi Mark,
I don't see a way around this at the moment. It does indeed look like you need to use the Gigabit Phy in...
09/30/2012
- 05:34 PM PCB Development: RE: Ethernet PHYs
- Hi Mark,
You are correct about the PR1_MII* signals, according to this E2E post, sorry about that.
http://e2e.t...
09/28/2012
- 11:57 AM PCB Development: RE: Ethernet PHYs
- Hi Mike,
The interfaces we definitely need out of the 335x are a 16 bit GPMC (to FPGA), 1 Ethernet (10/100 is fine... - 09:35 AM PCB Development: RE: Ethernet PHYs
- What other peripherals are you trying to accommodate? At a glance it looks like the pin outs should support RMII0 on...
- Please correct me if I'm wrong, but it appears the pin-muxing configuration for the MityARM-335x SOM is forcing the u...
- The PCB footprint found in section 6.5 of the MityARM-335x Carrier Board Design Guide can be misleading if you are no...
09/26/2012
- 10:10 AM PCB Development: RE: MityARM standard-keyed vs. reverse-keyed SO-DIMM connector
- We have not tested such a configuration, so I don't really know. If the electrical connections honor the spec, then ...
09/24/2012
- The MityARM design guide suggests an SO-DIMM connector with a standard keying. We have built our board with a revers...
09/21/2012
- 10:11 AM Software Development: RE: MityARM-335x Ethernet Communication
- Found the problem. The problem was related to the errata on the Vitesse VSC8601 Ethernet phy used on the development...
09/20/2012
- I am trying to get the TI StarterWare Enet_Echo example to run on the MityARM-335x Development Kit. To accomplish thi...
09/18/2012
- 04:36 PM Software Development: RE: mod_fastcgi.so
- Hi Scott,
Tried that with no luck...
however I was looking through the lighttpd documentation and saw I forgot t... - 02:45 PM Software Development: RE: mod_fastcgi.so
- Try "--host=arm-angstrom-linux-gnueabi" instead....
-Mike
- 02:30 PM Software Development: RE: mod_fastcgi.so
- Scott,
Downloaded from:
http://download.lighttpd.net/lighttpd/releases-1.4.x/
lighttpd-1.4.26.tar.gz 2010-Feb-07... - 12:38 PM Software Development: RE: mod_fastcgi.so
- Randy,
Could you give me a link to where you downloaded the lighttpd source? Also once you downloaded it, can you ... - 09:41 AM Software Development: RE: mod_fastcgi.so
- Hi Mike,
I found out the version of the lighttpd based on one of the included shared libraries.
I have downloaded...
09/17/2012
- 10:57 AM Software Development: RE: mod_fastcgi.so
- Hi Mike,
Should have mentioned Linux and Lighttpd are very new for me.
I had assumed I could just compile the light...
09/15/2012
- 06:36 AM Software Development: RE: mod_fastcgi.so
- So anyway, the mod-fastcgi.so should not require you to rebuild the kernel. You should be able to download it, "conf...
09/14/2012
- 12:54 PM Software Development: RE: mod_fastcgi.so
- What filesystem are you using? You might be able to get it installed using opkg.
-Mike
- Hi,
I'm trying to use fastcgi with the lighttpd web server. I have successfully create a simple example and changed ...
09/07/2012
- 12:29 AM Software Development: RE: Re-assigning the PHY_RESET
- Hi Tim,
Thanks for you quick reply. I managed to swap the PHY_RESET and get the Ethernet working - Brilliant!.
Than...
09/06/2012
- 10:01 AM Software Development: RE: Re-assigning the PHY_RESET
- Keith
The pinmux setup for the PHY reset should be done in u-boot. It is in board/cl/mityarm335x/mux.c in the rgmii2...
09/05/2012
- Hi,
I want to re-assign the PHY_RESET from gpio3_10 to gpio3_4. I can have included gpio3_4 in mux33xx.c but it ap...
Also available in: Atom
Go to top
