Project

General

Profile

Activity

From 09/06/2012 to 10/05/2012

10/04/2012

09:11 AM Software Development: RE: Ethernet Interface to Micrel KSZ9021 PHY.
Hi Raja,
I don't think we've used this PHY with the MityARM-3359 here, but we have had problems strapping this dev...
Michael Williamson

10/03/2012

03:31 PM Software Development: Ethernet Interface to Micrel KSZ9021 PHY.
Hi,
We are using MityARM SOM and MICREL KSZ9021RNI gigabit as PHY on it for Ethernet Interface.
We have configure...
Raja Vankam

10/01/2012

12:22 PM PCB Development: RE: Caution on MityARM SO-DIMM PCB Footprint
Mark,
Thank you for pointing out that lack of information. It has now been addressed and the design guide has been...
Alexander Block
07:40 AM PCB Development: RE: Ethernet PHYs
Hi Mark,
I don't see a way around this at the moment. It does indeed look like you need to use the Gigabit Phy in...
Michael Williamson

09/30/2012

05:34 PM PCB Development: RE: Ethernet PHYs
Hi Mark,
You are correct about the PR1_MII* signals, according to this E2E post, sorry about that.
http://e2e.t...
Michael Williamson

09/28/2012

11:57 AM PCB Development: RE: Ethernet PHYs
Hi Mike,
The interfaces we definitely need out of the 335x are a 16 bit GPMC (to FPGA), 1 Ethernet (10/100 is fine...
Anonymous
09:35 AM PCB Development: RE: Ethernet PHYs
What other peripherals are you trying to accommodate? At a glance it looks like the pin outs should support RMII0 on... Michael Williamson
08:49 AM PCB Development: Ethernet PHYs
Please correct me if I'm wrong, but it appears the pin-muxing configuration for the MityARM-335x SOM is forcing the u... Anonymous
08:26 AM PCB Development: Caution on MityARM SO-DIMM PCB Footprint
The PCB footprint found in section 6.5 of the MityARM-335x Carrier Board Design Guide can be misleading if you are no... Anonymous

09/26/2012

10:10 AM PCB Development: RE: MityARM standard-keyed vs. reverse-keyed SO-DIMM connector
We have not tested such a configuration, so I don't really know. If the electrical connections honor the spec, then ... Michael Williamson

09/24/2012

03:12 PM PCB Development: MityARM standard-keyed vs. reverse-keyed SO-DIMM connector
The MityARM design guide suggests an SO-DIMM connector with a standard keying. We have built our board with a revers... Ali Asgar Sohanghpurwala

09/21/2012

10:11 AM Software Development: RE: MityARM-335x Ethernet Communication
Found the problem. The problem was related to the errata on the Vitesse VSC8601 Ethernet phy used on the development... Anonymous

09/20/2012

09:49 AM Software Development: MityARM-335x Ethernet Communication
I am trying to get the TI StarterWare Enet_Echo example to run on the MityARM-335x Development Kit. To accomplish thi... Anonymous

09/18/2012

04:36 PM Software Development: RE: mod_fastcgi.so
Hi Scott,
Tried that with no luck...
however I was looking through the lighttpd documentation and saw I forgot t...
R D
02:45 PM Software Development: RE: mod_fastcgi.so
Try "--host=arm-angstrom-linux-gnueabi" instead....
-Mike
Michael Williamson
02:30 PM Software Development: RE: mod_fastcgi.so
Scott,
Downloaded from:
http://download.lighttpd.net/lighttpd/releases-1.4.x/
lighttpd-1.4.26.tar.gz 2010-Feb-07...
R D
12:38 PM Software Development: RE: mod_fastcgi.so
Randy,
Could you give me a link to where you downloaded the lighttpd source? Also once you downloaded it, can you ...
Scott Gerenser
09:41 AM Software Development: RE: mod_fastcgi.so
Hi Mike,
I found out the version of the lighttpd based on one of the included shared libraries.
I have downloaded...
R D

09/17/2012

10:57 AM Software Development: RE: mod_fastcgi.so
Hi Mike,
Should have mentioned Linux and Lighttpd are very new for me.
I had assumed I could just compile the light...
R D

09/15/2012

06:36 AM Software Development: RE: mod_fastcgi.so
So anyway, the mod-fastcgi.so should not require you to rebuild the kernel. You should be able to download it, "conf... Michael Williamson

09/14/2012

12:54 PM Software Development: RE: mod_fastcgi.so
What filesystem are you using? You might be able to get it installed using opkg.
-Mike
Michael Williamson
12:14 PM Software Development: mod_fastcgi.so
Hi,
I'm trying to use fastcgi with the lighttpd web server. I have successfully create a simple example and changed ...
R D

09/07/2012

12:29 AM Software Development: RE: Re-assigning the PHY_RESET
Hi Tim,
Thanks for you quick reply. I managed to swap the PHY_RESET and get the Ethernet working - Brilliant!.
Than...
Keith Fletcher

09/06/2012

10:01 AM Software Development: RE: Re-assigning the PHY_RESET
Keith
The pinmux setup for the PHY reset should be done in u-boot. It is in board/cl/mityarm335x/mux.c in the rgmii2...
Tim Iskander
 

Also available in: Atom

Go to top
Add picture from clipboard (Maximum size: 1 GB)