Project

General

Profile

Activity

From 07/10/2015 to 08/08/2015

07/30/2015

09:35 AM Software Development: RE: Load DTB from NAND
Angelos,
This would depend on what your trying to accomplish.
I believe the preferable way would be to have ub...
Jonathan Cormier
06:14 AM Software Development: RE: Load DTB from NAND
Hi Jonathan,
Thanks for your answer.
In my application, I would like to have three subpartitions inside the /ro...
Angelos Spanos

07/27/2015

11:47 AM Software Development: RE: Load DTB from NAND
There are several ways that data can have bitflips. See the below link for some cases. The minimum ECC level specifi... Jonathan Cormier
04:35 AM Software Development: RE: Load DTB from NAND
Hi Jonathan,
Thanks for the commands.
Could you please verify whether the erase blocks are only used and can be...
Angelos Spanos

07/24/2015

10:59 AM Software Development: RE: Load DTB from NAND
Angelos Spanos wrote:
> Hi Jonathan,
>
> Jonathan Cormier wrote:
> > Note that u-boot does need to be setup to u...
Jonathan Cormier
05:00 AM Software Development: RE: Load DTB from NAND
Hi Jonathan,
Jonathan Cormier wrote:
> Note that u-boot does need to be setup to use the backup environment.
...
Angelos Spanos

07/23/2015

11:36 AM Software Development: RE: Load DTB from NAND
I believe the backup partition is preferable, since u-boot will save the env in both so if one becomes corrupt there ... Jonathan Cormier
11:22 AM Software Development: RE: Load DTB from NAND
OK. So should I increase the partition by 256KiB or should I introduce the partition "NAND.u-boot-env.backup1"? Angelos Spanos
11:20 AM Software Development: RE: Load DTB from NAND
For the 512MB Nand an erase block is 256KB. It was 128KB on the 256MB Nand. Jonathan Cormier
11:16 AM Software Development: RE: Load DTB from NAND
Jonathan Cormier wrote:
> Angelos Spanos wrote:
> > Please let me know if you see any potential problems with this ...
Angelos Spanos
10:48 AM Software Development: RE: Load DTB from NAND
Angelos Spanos wrote:
> Hi Jonathan,
>
> Many thanks for your pointers.
>
> I have created a tested solution w...
Jonathan Cormier
09:38 AM Software Development: RE: Load DTB from NAND
Also, the solution you proposed should also work, but I haven't got around to testing it yet. If I do I will let you ... Angelos Spanos
09:36 AM Software Development: RE: Load DTB from NAND
The following commands were used for flashing the NAND from U-Boot:... Angelos Spanos
09:32 AM Software Development: RE: Load DTB from NAND
Hi Jonathan,
Many thanks for your pointers.
I have created a tested solution with a different partition scheme....
Angelos Spanos
09:21 AM Software Development: RE: Load DTB from NAND
We haven't gotten to testing the NAND support for the 3.14 kernel yet. Because of this I haven't looked at rearrangi... Jonathan Cormier
04:32 AM Software Development: Load DTB from NAND
Hi,
In the the text found here (https://support.criticallink.com/redmine/projects/armc8-platforms/wiki/UBIFS_Nand_...
Angelos Spanos

07/22/2015

12:20 PM Software Development: RE: Flat Device Tree source file configuration for 512MB NAND
Hi Jonathan,
I have just fixed it. The following changes were done:...
Angelos Spanos
11:49 AM Software Development: RE: Flat Device Tree source file configuration for 512MB NAND
Angelos Spanos wrote:
> Where is the Revision written? The Part Number is 80-00458RH-6
That is a Rev 6. So I'm n...
Jonathan Cormier
11:40 AM Software Development: RE: Flat Device Tree source file configuration for 512MB NAND
Jonathan Cormier wrote:
> Your welcome. I take this means you got 512MB Nand working. Were you able to use the bch...
Angelos Spanos
11:36 AM Software Development: RE: Flat Device Tree source file configuration for 512MB NAND
Your welcome. I take this means you got 512MB Nand working. Were you able to use the bch16 ECC? It would be helpfu... Jonathan Cormier
11:07 AM Software Development: RE: Flat Device Tree source file configuration for 512MB NAND
The problem as it is described on the subject of the ticket is now resolved.
I will probably open another ticket i...
Angelos Spanos
06:50 AM Software Development: RE: Flat Device Tree source file configuration for 512MB NAND
Attaching the latest am335x-mitysom.dts file with support for 512MB NAND. Angelos Spanos
06:16 AM Software Development: RE: Flat Device Tree source file configuration for 512MB NAND
With the following bootargs I can enter the filesystem:... Angelos Spanos
05:36 AM Software Development: RE: Flat Device Tree source file configuration for 512MB NAND
I have created a DTS file for the 512MB NAND. It is described below. Could you please confirm that the ... Angelos Spanos

07/21/2015

10:59 AM Software Development: RE: Flat Device Tree source file configuration for 512MB NAND
Angelos Spanos wrote:
> ??The commented out section was copied from TI's evm device tree. I've attached a patch from...
Jonathan Cormier
10:48 AM Software Development: RE: Flat Device Tree source file configuration for 512MB NAND
??The commented out section was copied from TI's evm device tree. I've attached a patch from our internal git which s... Angelos Spanos
10:38 AM Software Development: RE: Flat Device Tree source file configuration for 512MB NAND
Angelos Spanos wrote:
> We are developping on a 3354-HX-X38-RC MitySOM. I am currently using the default am335x-mity...
Jonathan Cormier
10:12 AM Software Development: RE: Flat Device Tree source file configuration for 512MB NAND
Adding the device tree source file used. Angelos Spanos
10:07 AM Software Development: Flat Device Tree source file configuration for 512MB NAND
We are developping on a 3354-HX-X38-RC MitySOM. I am currently using the default am335x-mitysom.dts file, which has t... Angelos Spanos
 

Also available in: Atom

Go to top
Add picture from clipboard (Maximum size: 1 GB)