Activity
From 05/28/2014 to 06/26/2014
06/26/2014
- BL 10:46 PM MitySOM-5CSX Altera Cyclone V FPGA Development: RE: How to access FPGA internal memory through AXI slave interface protocol
- Thanks for your reply.
I am currently intend to use hps2fpga bridge only in my design. And I just copy the generated rbf file into SD card and loaded it into FPGA by using "cat file.rbf > /dev/fpga0". By refering to the 2nd link from ... - MW 08:12 AM MitySOM-5CSX Altera Cyclone V FPGA Development: RE: How to access FPGA internal memory through AXI slave interface protocol
- Which AXI crossbar interface are you using? The hps2fpga bridge or the lightweight bridge? Did you make a new preloader?
Ref: http://www.altera.com/literature/hb/cyclone-v/cv_54005.pdf
You must ensure that you are enabling the br... -
01:00 PM
MitySOM-5CSX Altera Cyclone V
Software Development: UART RS232
- Hi,
Could you point to some examples for UART RS232 communication?
Thanks,
Jack - BD 11:22 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: SSD on MityDSP-L138F
- Hannes,
As mentioned in the errata, they do not recommend the "reset" approach because they cannot guarantee that it will work in a reasonable amount of time.
If you are going to go down this path, I suggest you test this approach ... - JC 08:25 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Where to download the document about Memory Map and Register Address of IO Board 80-000268RI-2C and OMAPL138F
- These are provided by TI. You can find them here: http://www.ti.com/product/OMAP-L138/technicaldocuments
You should start with the "OMAP-L138 C6000 DSP+ARM Processor (Rev. H)" Datasheet and the "OMAP-L138 C6000 DSP+ARM Processor Techn... - MW 08:16 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Where to download the document about Memory Map and Register Address of IO Board 80-000268RI-2C and OMAPL138F
- The memory map of the OMAP-L138 can be found on TI's main "OMAP-L138 web page":http://www.ti.com/product/omap-l138 (see the datasheet and the technical reference manual).
Not sure if that is what you are looking for.
06/25/2014
- only some brief documents are found in wiki,
Where can I download the document about Memory Map and Register Address of the IO Board 80-000268RI-2C and OMAPL138F? - Hi,
I have implemented a logic and loaded into cyclone V FPGA. Before that, I did run simulation to access a memory, which was generated by Megafunctions Wizard and is inside of FPGA. After I loaded the image of my design, I need to f... - JC 05:09 PM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: MityARM335x profile 1 - Model No: 3352-GX-X27-RC failing memory writes in u-boot
- Dirty gets appended to the version string for both u-boot and the kernel when you compile source code that has changes that aren't committed in git. Its a sort of warning to the developer that this version may not be reproducible from a...
-
05:05 PM
MitySOM-335x (ARM Cortex-A8 Based Products)
Software Development: RE: MityARM335x profile 1 - Model No: 3352-GX-X27-RC failing memory writes in u-boot
- I pulled the AM335XPSP_04.06.00.08 tag and there were a lot of differences. I don't think it matters
that much as we really only modify six files of yours, and most of that is because of the one very
large SPI NOR chip that we need. I'... - JC 04:58 PM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: MityARM335x profile 1 - Model No: 3352-GX-X27-RC failing memory writes in u-boot
- Looks like both the 03 and 08 branches have the same 2011.09 date so harder to determine which branch of code you were using.
- JC 04:55 PM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: MityARM335x profile 1 - Model No: 3352-GX-X27-RC failing memory writes in u-boot
- You were likely using the code from the AM335XPSP_04.06.00.08 branch before and now should be using the u-boot-2013.10 branch. There may be alot of changes between the two branches.
-
02:05 PM
MitySOM-335x (ARM Cortex-A8 Based Products)
Software Development: RE: MityARM335x profile 1 - Model No: 3352-GX-X27-RC failing memory writes in u-boot
- Hey Jonathan,
Can you tell me if I were to pull a full u-boot "tree" from your "u-boot-mityarm-335x.git/tree", which one of
the head labels should I use? u-boot-2013.10, AM335XPSP_04.06.00.03 or AM335XPSP_04.06.00.08 ?
I'll... -
12:18 PM
MitySOM-335x (ARM Cortex-A8 Based Products)
Software Development: RE: MityARM335x profile 1 - Model No: 3352-GX-X27-RC failing memory writes in u-boot
- Seems like when I used our NAND mlo/u-boot burn in scripts, I blasted over the old u-boot by erasing NAND from 0 to 0x1E0000.
Sorry for the distraction. -
12:11 PM
MitySOM-335x (ARM Cortex-A8 Based Products)
Software Development: RE: MityARM335x profile 1 - Model No: 3352-GX-X27-RC failing memory writes in u-boot
- Not sure what happened, but even placing the original MLO back it will not boot:
U-Boot SPL 21401-101.01.00.02-dirty (Nov 06 2013 - 08:59:11)
Texas Instruments Revision detection unimplemented
MityARM335x profile 1 - Model No: 3352... -
12:02 PM
MitySOM-335x (ARM Cortex-A8 Based Products)
Software Development: RE: MityARM335x profile 1 - Model No: 3352-GX-X27-RC failing memory writes in u-boot
- Booting from the mmc card now does not show that u-boot in NAND has any issues.
U-Boot# nand read 8d000000 80000 1e0000
NAND read: device 0 offset 0x80000, size 0x1e0000
1966080 bytes read: OK
U-Boot# - JC 11:56 AM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: MityARM335x profile 1 - Model No: 3352-GX-X27-RC failing memory writes in u-boot
- Yes we decided to store everything in nand using the correct ecc so we disabled the nandecc command. So you do not need to change ecc modes anymore in u-boot.
Odd I wasn't aware of any compatibility problems with loading the old u-bo... -
11:43 AM
MitySOM-335x (ARM Cortex-A8 Based Products)
Software Development: RE: MityARM335x profile 1 - Model No: 3352-GX-X27-RC failing memory writes in u-boot
- Looks like we can't reach u-boot with the new MLO. We see the following and then it stops. If we plug in the
mmc, we are back. Any suggestions?
John C.
U-Boot SPL 2013.10-gd35e056 (Jun 03 2014 - 17:00:30)
MitySOM335x profile 1 -... -
11:34 AM
MitySOM-335x (ARM Cortex-A8 Based Products)
Software Development: RE: MityARM335x profile 1 - Model No: 3352-GX-X27-RC failing memory writes in u-boot
- Thanks Jonathan,
It seems the u-boot nandecc command has changed. We used to run the following script for
burning all four MLO locations. When we ran the "nandecc hw 2" command it used to come back
with a "HW ECC BCH8 Selected" r... - JC 11:17 AM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: MityARM335x profile 1 - Model No: 3352-GX-X27-RC failing memory writes in u-boot
- Okay. I created a FAQ about this issue incase anyone else runs into it.
https://support.criticallink.com/redmine/projects/armc8-platforms/wiki/Software_FAQs#U-boot-has-started-hanging-on-startup-while-booting-from-nand-or-is-behaving-... -
11:13 AM
MitySOM-335x (ARM Cortex-A8 Based Products)
Software Development: RE: MityARM335x profile 1 - Model No: 3352-GX-X27-RC failing memory writes in u-boot
- Hey Jonathan,
Yes there is indeed an error. I'll try the newer MLO to see how that works.
Thanks,
John C.
U-Boot# nand read 8d000000 0 80000
NAND read: device 0 offset 0x0, size 0x80000
524288 bytes read: OK
U-Boot#... - JC 10:18 AM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: MityARM335x profile 1 - Model No: 3352-GX-X27-RC failing memory writes in u-boot
- If you confirm there are bit flips you can then flash just the UBL into the NAND and see if it boots fine. You'll see something like the following during boot to show that its correcting the bit flips.
- JC 10:13 AM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: MityARM335x profile 1 - Model No: 3352-GX-X27-RC failing memory writes in u-boot
- Try doing to following. It should print out bitflips if it finds them.
-
09:53 AM
MitySOM-335x (ARM Cortex-A8 Based Products)
Software Development: RE: MityARM335x profile 1 - Model No: 3352-GX-X27-RC failing memory writes in u-boot
- Hey Jonathan,
I don't have access to a booted Linux, only u-boot. I created a text script that runs the u-boot "nand dump <address>" from address 80000h to F0000h in increments of 800h = 2048 (page size.) The output is raw (see inc... - LY 04:02 PM MityDSP-L138 (ARM9 Based Platforms) FPGA Development: RE: DSP to FPGA SPI Setup Question
- Hello,Mike
Thank you very much.
- MW 12:42 PM MityDSP-L138 (ARM9 Based Platforms) FPGA Development: RE: DSP to FPGA SPI Setup Question
- What is your target update rate? Continuous?
You might try first to rip out all of the overhead on the tcDspFpgaSpi.cpp code (there is LCK_pend()/LCK_post() for serialization control, etc) and boil it down to the register writes.
... - LY 11:32 AM MityDSP-L138 (ARM9 Based Platforms) FPGA Development: RE: DSP to FPGA SPI Setup Question
- Hello,Mike
Thank you for your help.
I have attached two pic
----one is the SPI bits transfer rate(This is our desired speed),
----another one is the word to word transfer rate(This is slow. We want it can be fast,Could you give u... - MW 10:47 AM MityDSP-L138 (ARM9 Based Platforms) FPGA Development: RE: DSP to FPGA SPI Setup Question
- Can you check with a scope at what the clock rate is on the SPI device, and the interword write delay? I just want to confirm they are getting 50 MHz clock rate.
It might be the EMIFA transfer, but we should confirm that the SPI de... - AB 10:39 AM MityDSP-L138 (ARM9 Based Platforms) FPGA Development: RE: DSP to FPGA SPI Setup Question
- Update and followup question from the customer:
We have made the SPI work, but transmitting the word to word is slow.(about 11 uSec to send a 24bit word).
This is the code we run in the DSP:
spi = new tcDspFpgaSpi((void *)my_bas... - MF 12:01 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Interrupting the ARM from the DSP
- Thanks. This does what I wanted.
On the DSP side: - MW 09:11 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Interrupting the ARM from the DSP
- I think that you are confusing signals and interrupts a bit.
You need to write some kernel module code to register an ISR handler for the CHIPSIG (which may already being used by DSPLINK) and forward/create the signal condition you ar... - MF 08:26 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Interrupting the ARM from the DSP
- Yes, I am familiar with DSPLink and am using it. However, I have time requirement that DSPLink cannot meet. Polling uses too much CPU time. Interrupt would be the most efficient. I just need to know how to connect the CHIPSIG interrup...
- HK 08:01 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: USB2.0 Host on MityDSP-L138F
- There you are. Note that i had to change the initialization in the code as noted above.
- MW 07:26 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: USB2.0 Host on MityDSP-L138F
- If you don't mind, could you post your config.gz file?
- HK 05:37 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: USB2.0 Host on MityDSP-L138F
- Hey again,
i tried changing it from DMA to PIO. Now, everything seems to work. Device is readable, writable and mountable. Performonce is ok - about 8MB/s either way.
The ethernet problem is gone. I'm not sure where the problem was... - Hey folks,
I'm trying to use a SSD instead of a HDD on the L138F.
I found in the errata that the OMAP-L138 has a problem with SATA devices capable of SATA 3. I'm using a Samsung 840 evo.
The kernel detected the disk once, but ... - AM 02:12 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: TPS65023 VDCDC2 and VDCDC3 constraints
- Jonathan, thank you, I will track your branch.
06/24/2014
- GG 05:41 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Interrupting the ARM from the DSP
- Hello Mary,
I'm not sure what the problem is in your specific example as we almost always use DSPLink to to communicate between the ARM and DSP. We have wrapper classes that allow for passing messages between the DSP and ARM, and uti... - I would like to have the DSP (running BIOS 5) interrupt the ARM (running Linux MDK_2012-08-10)
In the DSP Code: - JC 05:19 PM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: MityARM335x profile 1 - Model No: 3352-GX-X27-RC failing memory writes in u-boot
- That is what I'm suggesting. You can verify if this is the issue by running the 'nand dump' or 'nand read' command and looking for any reported fixed bitflips.
Note you can try this from linux as well. The -n option should allow you... -
05:07 PM
MitySOM-335x (ARM Cortex-A8 Based Products)
Software Development: RE: MityARM335x profile 1 - Model No: 3352-GX-X27-RC failing memory writes in u-boot
- So let me try and clarify the issue. We have been running our u-boot for about 10 months with no issues. Are you suggesting that a bit has gone bad and because the older MLO did not set ecc correctly, we are now seeing this strang behavi...
- JC 04:56 PM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: MityARM335x profile 1 - Model No: 3352-GX-X27-RC failing memory writes in u-boot
- Those ecc errors are coming from reading the environment from nand. If I remember correctly the older u-boot saved the environment using a 1 bit ecc (hamming) instead of 8 bit ecc (bch-8) which the new u-boot uses for everything. You ca...
- JC 04:49 PM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: MityARM335x profile 1 - Model No: 3352-GX-X27-RC failing memory writes in u-boot
- No nevermind, thats not correct. You do have a 256MB nand module. So the first u-boot should be correct.
- JC 04:47 PM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: MityARM335x profile 1 - Model No: 3352-GX-X27-RC failing memory writes in u-boot
- U-Boot mainline:
origin/u-boot-2013.10: d35e05656457c2d3715de8c3eb7c777375c160ae
u-boot config: mityarm335x_4kpage_config - JC 04:46 PM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: MityARM335x profile 1 - Model No: 3352-GX-X27-RC failing memory writes in u-boot
- Woops hangon didn't notice that you had a 3352 module. They have a larger nand and require a special u-boot build.
-
04:40 PM
MitySOM-335x (ARM Cortex-A8 Based Products)
Software Development: RE: MityARM335x profile 1 - Model No: 3352-GX-X27-RC failing memory writes in u-boot
- Hey Jonathan,
Something is very unhappy. Here is the boot:
CCCCCCCC
U-Boot SPL 2013.10-gd35e056 (Jun 03 2014 - 17:00:30)
MitySOM335x profile 1 - Model No: 3352-GX-X27-RC Serial No: 134253
Configuring for 256 MB DDR3 @ 400MHz
C... - JC 04:28 PM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: MityARM335x profile 1 - Model No: 3352-GX-X27-RC failing memory writes in u-boot
- There was a bug with the older u-boot where ecc was not enabled when the UBL loaded the u-boot image. This meant that bitflips could cause weird error messages. Seeing as you don't have any problems when the u-boot is loaded from mmc, ...
-
04:22 PM
MitySOM-335x (ARM Cortex-A8 Based Products)
Software Development: RE: MityARM335x profile 1 - Model No: 3352-GX-X27-RC failing memory writes in u-boot
- Here is the boot sequence:
----------------------------------------------------------------
U-Boot# CCCCCCCC
U-Boot SPL 21401-101.01.00.02-dirty (Nov 06 2013 - 08:59:11)
Texas Instruments Revision detection unimplemented
MityARM335x... - JC 04:14 PM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: MityARM335x profile 1 - Model No: 3352-GX-X27-RC failing memory writes in u-boot
- John,
What version of U-boot are you using? If you can include the full bootlog that would be helpful. -
03:59 PM
MitySOM-335x (ARM Cortex-A8 Based Products)
Software Development: RE: MityARM335x profile 1 - Model No: 3352-GX-X27-RC failing memory writes in u-boot
- As added information, the mtest command works.
Commands that *do* work:
mtest 402fffe0 402ffffe A5A500FF
mtest 80000000 8d000000 A5A500FF
Commands that *don't* work:
mw.b 8d000000 A
mw.b 402fffe0 A
mw.w 402fffe0 A
mw.l 402fff... -
03:24 PM
MitySOM-335x (ARM Cortex-A8 Based Products)
Software Development: MityARM335x profile 1 - Model No: 3352-GX-X27-RC failing memory writes in u-boot
- We just received one of our units back from the field and it hangs running a "mw.b" command in the u-boot param script. The system will lock up using DDR or internal ARM memory addresses in the mw.b command. If we boot off the mmc sd car...
- JC 12:04 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: TPS65023 VDCDC2 and VDCDC3 constraints
- Andrey,
Not sure if its any help but I've pushed a work in progress 3.14 branch to our git. Its based off the mainline 3.14.y branch. Haven't been able to get SPI working so the ethernet isn't getting initialized as its configured fr...
06/23/2014
- ES 10:25 AM MityDSP-L138 (ARM9 Based Platforms) PCB Development: RE: MityDSP-L138 processor running hot
- All unused connections are no connects.
- ES 09:59 AM MityDSP-L138 (ARM9 Based Platforms) PCB Development: RE: MityDSP-L138 processor running hot
- I have attached a plot showing the rise of the supply on the baseboard (channel 2) and the Mity card (channel 1). As you can see there is a droop in the supply on the card. I assume there is a switch mode regulator to generate the 1.8V f...
- MW 09:54 AM MityDSP-L138 (ARM9 Based Platforms) PCB Development: RE: MityDSP-L138 processor running hot
- What are you doing with unused connections on the module?
- ES 09:52 AM MityDSP-L138 (ARM9 Based Platforms) PCB Development: RE: MityDSP-L138 processor running hot
- It remains hot until the next power cycle. A reset cycle alone does not give an improvement.
- MW 09:15 AM MityDSP-L138 (ARM9 Based Platforms) PCB Development: RE: MityDSP-L138 processor running hot
- On non-FPGA variants, DVDD3318_A, DVDD3318_B, and DVDD3318_C are all tied to 3.3V.
Does the issue only occur during reset, or once the unit boots it remains "hot" until another power cycle or reset cycle? - ES 09:07 AM MityDSP-L138 (ARM9 Based Platforms) PCB Development: RE: MityDSP-L138 processor running hot
- All our I/O to the card is 3.3V. The OMAP processor has 3 configurable power groups which can be connected to 3.3V or 1.8V. I believe you have them all connected to 3.3V but as I don't have your circuit I cannot verify this. Could you co...
- MW 07:56 AM MityDSP-L138 (ARM9 Based Platforms) PCB Development: RE: MityDSP-L138 processor running hot
- Ok.
I suspect the issue may be related to I/O voltage levels (you have I/Os being driven or pulled to a value larger than the bank voltage), or during reset the OMAP-L138 typically pulls most of it's I/O pins (internally) to +VDD of w... - ES 07:51 AM MityDSP-L138 (ARM9 Based Platforms) PCB Development: RE: MityDSP-L138 processor running hot
- We are using a baseboard developed for our application. I'm happy to share the schematic. Let me know how to get that to you. The variant we are running is without the FPGA.
I have managed to measure the excess current draw. When it i... - MW 07:06 AM MityDSP-L138 (ARM9 Based Platforms) PCB Development: RE: MityDSP-L138 processor running hot
- Hi Ed,
Are you running on a DevKit or on a custom board? Would you be willing to share your schematic (privately to CL, not via this forum page)? Are you using an FDGA variant or processor only variant of the module?
-Mike
- We are some way into the development of using the MityDSP-L138 platform. I recently noticed that about 50% of the time when the module is powered up the OMAP processor runs very hot, >50C. The other 50% of the time it runs relatively coo...
06/21/2014
- AM 03:49 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: TPS65023 VDCDC2 and VDCDC3 constraints
- Jonathan, nothing special only setup kernel config (attached).
I use Yocto Project Daisy toolchain and kernel from git://git.yoctoproject.org/linux-yocto-3.14.git, branch "standard/base".
But I'm not checked all peripherals. Can conf...
06/20/2014
- I am having some trouble with a data acquisition system.
Using MDK_2012-08-10
There are two tasks (among others) that perform the data acquisition. The data is streaming in from the mcBSP and is loaded into a common buffer by the ... - JC 02:12 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: TPS65023 VDCDC2 and VDCDC3 constraints
- Andrey, Can you share your linux 3.14 port. What did you have to change to get it working? Are you using device tree?
Thanks Jonathan - Hello,ALL
I want to test the DspFpgaSpi, but not successfully setup,Could anyone give me some instructions?
Before I have successfully tested the GPIO from your help, Thank you very much!
This the VHDL code Setup
//////////////////... - MW 08:45 AM MitySOM-5CSX Altera Cyclone V Software Development: RE: Using custom DTS in yocto flow
- Right now, the kernel recipe that gets used for our dev kit is indeed in the meta-mitysom-5csx/recipes-kernel/linux folder.
You will need to get familiar with "bitbake":http://www.yoctoproject.org/docs/1.6/bitbake-user-manual/bitbak...
06/19/2014
- GG 09:13 PM MityDSP-L138 (ARM9 Based Platforms) FPGA Development: RE: Looking for help about SPI core communicate with DSPFPGAspi
- Hello,
Your CORE_GPIO_MODULE and base address (0x66000080) do not match one another. The address should be the CORE offset times 0x80 bytes + 0x66000000.
So - LY 02:26 PM MityDSP-L138 (ARM9 Based Platforms) FPGA Development: RE: Looking for help about SPI core communicate with DSPFPGAspi
- Hello.
Ask the same questions about the GPIO
I also try to use the DSP to communicate with FPGA
The follow is the VHDL code for gpio setup
/----------------------------------------------------------------------------/
--Gpio setup... - GG 01:09 PM MityDSP-L138 (ARM9 Based Platforms) FPGA Development: RE: Looking for help about SPI core communicate with DSPFPGAspi
- Hello,
- LY 03:27 PM MityDSP-L138 (ARM9 Based Platforms) FPGA Development: RE: Help me check out the gpio Setup,It is not work.
- Thank you very much,Mike
- MW 03:11 PM MityDSP-L138 (ARM9 Based Platforms) FPGA Development: RE: Help me check out the gpio Setup,It is not work.
- The address for the constructor is not correct. The Address is: the CORE offset times 0x80 bytes + 0x66000000.
In your example, it should be 4*0x80 = 0x66000200.
The code looks OK, though you only need a 0x1 instead of a 0x3 for w... - Hello.
Ask the same questions about the GPIO
I also try to use the DSP to communicate with FPGA
The follow is the VHDL code for gpio setup
/----------------------------------------------------------------------------/
--Gpio setup... - AM 08:54 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: TPS65023 VDCDC2 and VDCDC3 constraints
- Mike, thank you for fast response.
In Linux 3.14 (from Yocto Project) this leads to disabling cpufreq because it cant locate CVDD regulator.
How you think can I simply change constraints? This doesn't broke my MityDSP?
- MW 08:29 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: TPS65023 VDCDC2 and VDCDC3 constraints
- In the hardware, the TPS65023 used for the MityDSP-L138 has the following voltages that are defaulted using the hardware strapping pins:
VDCDC1 -> 1.2 V (core)
VDCDC2 -> 1.8 V (mDDR, DVDD18, DVDD3318_C, FPGA bank voltages)
VDCDC3 -... - Hello,
I use MityDSP-L138F and Linux kernel from git://support.criticallink.com/home/git/linux-davinci.git but want upgrade to 3.14. I found inconsistent config of TPS65023 in board-mityomapl138.c. This file describe tps65023_regulato...
06/18/2014
- Posting on behalf of a customer and for future reference as well:
How do you get yocto to use a custom dts instead of the socfpga_mitysom5csx_devkit.dts?
The customer will be checking the kernel source and dts into version control ... - JC 12:57 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: USB2.0 Host on MityDSP-L138F
- When I enabled the dma I got the following errors when i plugged in the flash drive.
- JC 11:07 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: USB2.0 Host on MityDSP-L138F
- I was able to scp a 12 MB file without any errors
- JC 11:05 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: USB2.0 Host on MityDSP-L138F
- Also you can buy the cables prebuilt.
USB mini 5 pin to USB A Female
http://www.amazon.com/USB-Female-Mini-Male-Adapter/sim/B0016RNX2I/2 - JC 10:41 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: USB2.0 Host on MityDSP-L138F
- How were you experiencing the unstable ethernet? Just transferring a file?
- HK 10:36 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: USB2.0 Host on MityDSP-L138F
- That changed stuff a bit. I now get more messages and the usb-msd driver seems to wake up.
But during initialization, i get error messages of disconnect and reconnect - see the attached log. I'm not sure whether the problem's in the c... - BD 10:12 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: USB2.0 Host on MityDSP-L138F
- Hannes, please let us know if this resolves your issue. We actually fixed this same problem on our MitySOM-335x module a few days before you posted your question.
For the sake of those searching the forum in the future, the MitySOM-3... - JC 09:54 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: USB2.0 Host on MityDSP-L138F
- Got it working.
- HK 09:11 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: USB2.0 Host on MityDSP-L138F
- I don't think so. Udev primarily loads the driver and gets called once the driver does something. In the boot log you can see that the usb enumeration hangs during kernel initialization (usb is compiled in) and before init (and therefor ...
- MW 09:03 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: USB2.0 Host on MityDSP-L138F
- Wondering if this is perhaps a udev issue?
- HK 08:58 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: USB2.0 Host on MityDSP-L138F
- Exactly. But the mass storage driver itself gets loaded and then stalls (no /dev/sd* gets created).
- JC 08:23 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: USB2.0 Host on MityDSP-L138F
- Ok I was able to get things to the point where it will atleast detect the insertion of the flash drive by changing the usb register from MUSB_OTG to MUSB_HOST. I suspect that this is where you are at.
- HK 01:52 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: USB2.0 Host on MityDSP-L138F
- I tried changing between PIO and DMA before. That changed nothing about the problem - It enumerates the device and then stops.
Another thing:
If I plug in an external USB hub, the Linux detects that. Afterwards if i plug anything in,...
06/17/2014
- Hello,All
I have followed the instruction posted by Michael Williamson. The spi core on FPGA
--https://support.criticallink.com/redmine/boards/12/topics/1672?r=2036#message-2036
I built the FIFO using the IP CORES and put the SPI ... - JC 11:51 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: USB2.0 Host on MityDSP-L138F
- Heres my bootlog. I'm having a hard time getting the mini usb working at all, in either host or peripheral mode. I haven't tried switching from PIO only to the DMA driver you enabled. Did you find that fixed something for you?
- HK 10:11 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: USB2.0 Host on MityDSP-L138F
- There you are.
That's the dmesg right after startup, with the card reader plugged in during startup. I enabled USB-MSD debug messages, so there's a bit more noise from that.
I'm also getting - TI 09:40 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: USB2.0 Host on MityDSP-L138F
- OT: Hannes, can you please double check your email address in your profile, I (admin) am getting bounced email warnings for every update to this thread.
thank you
/Tim Iskander - JC 09:27 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: USB2.0 Host on MityDSP-L138F
- Could you post a full boot log? I'd like to compare it with what I'm getting. Also would be nice to see the connection log for the working port for comparison.
- HK 04:16 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: USB2.0 Host on MityDSP-L138F
- Hi Bob,
Here's the file.
Thanks
Hannes - MW 11:04 AM MitySOM-5CSX Altera Cyclone V Software Development: RE: I2C Access with 5CSX Development Board
- 1) i2cset and i2cget are pretty standard tools, do you need help installing them or do you not want them on your final OS? We can provide an RPM package for them if you are using the standard filesystem provided with the DevKit.
2) t...
06/16/2014
- BD 10:08 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: USB2.0 Host on MityDSP-L138F
- Hannes,
Can you upload your kernel .config file? We have seen similar problems on our 335x product line that were traced to an improper kernel configuration.
Thanks,
-Bob
- Hello everyone,
I'm trying to use the USB2-OTG on the MityDSP-L138F as a USB2 Host to connect a few USB-Mass Storage devices.
I'm using the current MDK (2014-01-13) on the supplied Development Board (industrial-i/o). I changed in a...
06/13/2014
- Posting on behalf of a customer and for future reference as well:
1) How do I access the +5V I2C current monitor IC interface on the Critical Link development board, WITHOUT using i2cSet and i2cGet? I do not have these programs instal...
06/10/2014
-
07:55 PM
MitySOM-5CSX Altera Cyclone V
Software Development: RE: Reading memory into a file
- Actually don't worry about it.
We managed to solve it.
Thanks,
Jack
06/09/2014
-
01:46 PM
MitySOM-5CSX Altera Cyclone V
Software Development: RE: Reading memory into a file
- Hi Greg,
Any update on this?
Did you guys manage to resolve the issue?
Thanks,
Jack
06/06/2014
- UF 06:36 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: DSP HelloWorld
- Flashing the 2014 MDK files solved all the problems. For some reason installing the U-boot bricked my board, but following the wiki on "reprogramming a dead board" fixed it.
I have another question. Is there a sample Makefile for buil... - JC 08:37 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: DSP HelloWorld
- The filesystem and kernel that ship preprogrammed on the L138 is quite old. You should have more luck if you flash the u-boot, kernel, and filesystem included in the 2014-01-13 MDK.
Installing U-boot:
https://support.criticallink.co... - BD 10:02 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Login uncorrect from serial connection and correct from ethernet connetion
- Silvano, as a test, you can rename the securetty file which should eliminate any restrictions on root logins.
- JC 09:51 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Login uncorrect from serial connection and correct from ethernet connetion
- My securetty file has following at the top of the file which i didn't see in the file you posted.
- JC 09:49 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Login uncorrect from serial connection and correct from ethernet connetion
- I updated to the latest filesystem and got similar results to my previous post.
- JC 08:54 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Login uncorrect from serial connection and correct from ethernet connetion
- Testing this on a L138 at my desk. I am able to login as root over ssh using any password including an empty password. But am having no trouble logging in over the serial port.
After setting a password I can no longer login using ... - SB 08:47 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Login uncorrect from serial connection and correct from ethernet connetion
- Is there something wrong?
Any idea? - SB 08:19 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Login uncorrect from serial connection and correct from ethernet connetion
- Attached you can find:
- a startup screenshot;
- the content of /etc/ folder;
- the file securetty.
Let me know, thanks.
Silvano - SB 08:01 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Login uncorrect from serial connection and correct from ethernet connetion
- From serial I do the access without password but when I write "root" at login it tells me "login incorrect".
From ethernet cable I do the access with "root" and password "mitydsp" but I do not set anything. - TI 08:00 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Login uncorrect from serial connection and correct from ethernet connetion
- Normally, this is not a problem. can you check if there is an /etc/securetty file ( http://www.faqs.org/docs/securing/chap5sec41.html )
or log in over the network and then try to log in from the serial console and check the log files in... - MW 07:58 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Login uncorrect from serial connection and correct from ethernet connetion
- Did you set a password for the root shell? Normally there is no password by default. How did you set the password?
-Mike
- SB 07:57 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Login uncorrect from serial connection and correct from ethernet connetion
- Does anybady has any suggestion?
It is important for me, not only to have the access from ethernet, but also from serial cable...
06/05/2014
- I'm trying to setup a development environment for the MityDSP-L138 to write DSP code.
I got the DSP HelloWorld test to work, but with a few blocking issues:
1. I had to use the HelloWorld program downloaded from the website. My own... - Dear all,
I have a strange problem.
I hava my MityDSP connected to my pc through both a serial cable and a ethernet cable.
The MityDSP works good. I installed the kernel on the SPI-FLASH and the file system in .jffs2 format on the... - SB 06:24 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Kernel loading module problems MityDSP and FPGA configuration
- I have corrected all the CRC error rounding the filesize parameters to the correct values.
I have also recompiled the kernel modifyind a little our configuration baseboard-industrialio.c file beacuse we noticed that there was one error ...
06/04/2014
- MW 08:57 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Kernel loading module problems MityDSP and FPGA configuration
- The filessize should be rounded to 0x800 bytes, which I think should be 0x150C800, not 0x150E000.
-Mike
- SB 08:49 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Kernel loading module problems MityDSP and FPGA configuration
- Dear all
As I got a lot of CRC errors, here are some question:
1 My .jffs2 file is about 21 MB (22070432 bytes) which corresponds to 0x150C4A0. To copy the filesystem on the target I use the following commands, right?
u-Boot> mw.b 0...
06/03/2014
- SB 08:48 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Kernel loading module problems MityDSP and FPGA configuration
- Dear Michael,
I tried to run the command you told me. Everything was ok until I copied the fpga_ctrl file on the target machine as you can see in the attached file fpga_ctrl_ontarget.png.
But when I run the "insmod" command I got wha...
06/01/2014
- AS 11:49 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: How to run bin application via u-boot?
- > If I knew the answer to using a bin file beyond "go", as you asked before, I would have told you before. :^)
I'm Sorry for my insistence.
> ...
No, the size didn't change much (debug out size is 3.06 MB and release out size is 2.8... - MW 10:19 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: How to run bin application via u-boot?
- Hi Ahmed,
If I knew the answer to using a bin file beyond "go", as you asked before, I would have told you before. :^)
So you set the --symdebug:none option and the filesystem grew on your Release build from 2MB to 3MB? That's odd... - AS 04:39 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: How to run bin application via u-boot?
- Hi Mike,
I have set the compiler option to "--symdebug:none" and the size of the .out file generated is also 3 MB.
Is there another option to minimize the size of out file? and as i asked you before is there a Uboot command to execute ...
05/30/2014
- MW 11:02 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Kernel loading module problems MityDSP and FPGA configuration
- Did you also rebuild the FPGA drivers? They are not in-tree in the kernel git repository. They are located in the board support package in the MityDSP Developer's Kit.
Let's start with this:
On the build machine: - SB 10:40 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Kernel loading module problems MityDSP and FPGA configuration
- Dear Michael,
let me know if my way of working is right:
1) I wrote my own baseboard-industrialio.c file as reported in the firts post of this discussion.
2) I recompiled the kernel as reported in https://support.criticallink.com/re... - MW 07:30 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Kernel loading module problems MityDSP and FPGA configuration
- Hello,
We have many customers able to load and run modules with the MityDSP-L138, it's not obvious what the issue is here. I am suspicious that there may have been a problem with the filesystem installation / update (either the modul... - SB 04:00 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Kernel loading module problems MityDSP and FPGA configuration
- Dear all,
attached you can find a text (LinuxLoading.txt) file where I captured the entire boot together with the screenshot where "Failed" occurs (FailuresLoadingKernel.png).
I also run "uname -a" and the results are in the text fil... - AS 03:45 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: How to run bin application via u-boot?
- Michael Williamson wrote:
> Just to confirm, you have the compiler option "--symdebug:none" in your release compile and link options?
> ...
Thanks Mike.
Unfortunately I didn't check this compiler option and now It's my weekend so I'll...
05/29/2014
- AB 04:29 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: How to run bin application via u-boot?
- Ahmed,
I believe Mike was suggesting that you build the application as a "release" version without any debugging and see what the resulting application file size is?
I.E. if it was 5MB in debug maybe it's 2MB in release, thus no ne... - MW 04:04 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: How to run bin application via u-boot?
- Just to confirm, you have the compiler option "--symdebug:none" in your release compile and link options?
-Mike
- AS 03:51 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: How to run bin application via u-boot?
- Hi Mike,
I have tried what you mentioned and it didn't work.
I'll wait your trial.
Thanks in advance. - MW 03:02 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: How to run bin application via u-boot?
- I think you need to strip the .out file (make a release version that removes the debugging information).
If I get a second I will try it out.
-Mike
- AB 01:48 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: How to run bin application via u-boot?
- Posting some previous direct followup e-mails from the customer.
I have followed the steps of the Starterware wiki ([[https://support.criticallink.com/redmine/projects/arm9-platforms/wiki/StarterWare]]) and I could run elf (UART_MITY_... - MW 10:47 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Kernel loading module problems MityDSP and FPGA configuration
- Hi,
Can you please capture the entire boot up on the console to a text file and set it over?
Or at least run "uname -a" and report the results?
-Mike
- SB 10:38 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Kernel loading module problems MityDSP and FPGA configuration
- Dear Bob,
when I try to load the modules with "insmod fpga_ctrl.ko" I get an error with "Function non implemented" as explanation.
I also found on internet that the insmod error message is caused by either a kernel lacking module sup... - BD 09:30 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Kernel loading module problems MityDSP and FPGA configuration
- Hi Silvano,
Jon was referring to the kernel modules explicitly. The modules need to be installed in your target root filesystem (/lib/$kernelversion) after you copy over the kernel.
The page you reviewed, does mention this, but it'... - SB 08:47 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Kernel loading module problems MityDSP and FPGA configuration
- I report before that I recompile the kernel every time I made a modificatuon on the baseboard file.
In fact the link you report me is cited by me in my first message.
Maybe there is something wrong in the file or in the compiling.
Cou... - JC 08:24 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Kernel loading module problems MityDSP and FPGA configuration
- Its hard to tell from those error messages whats going on but have you tried recompiling the kernel modules when you made changes to the kernel?
See https://support.criticallink.com/redmine/projects/arm9-platforms/wiki/FPGA_Core_Devic... - Hello everybody.
I am Silvano Bertoldo, I mainly work on the software side of MityDSP and I have a big problem about the linux kernel I am not able to solve. I am very grateful if you can support me or forward the present email to a s... - JC 09:53 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Compiler does not run in VM
- Also our vm does come with the toolchain installed. I'm unsure why you were unable to locate it.
Try looking in /usr/local/oecore-i686
The instructions seem to be missing that you need to run @. /usr/local/oecore-i686/environment-s... - MW 09:29 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Compiler does not run in VM
- Yes. You need to run the 32-bit version in the VM if your VM is a 32-bit architecture.
on your VM type "uname -a". It should tell you the version of the VM architecture.
-Mike - Hello- I'm new to the MityDSP platform and I am having trouble getting the development environment working. I have imported the VM into VirtualBox, and can run the VM. I'm trying to get the environment going for the L138F (ARM9). I fo...
05/28/2014
- Hi everyone,i have MityARM1808F.
I could use "bootelf" command[ex: bootelf 0xc0700000] to run any app.out,but the size of .out format is usually large(in my case is about 5 Mega byte which is too large to be saved on SPI flash with FPGA... - AS 08:54 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: UPP ISR is not called
- Finally i could solve this issue by adding the following code :
asm(" mrc p15, #0, r0, c1, c0, #0\n\t"
" orr r0, r0, #0x00002000\n\t"
" mcr p15, #0, r0, c1, c0, #0\n\t");
before calling BIOS_start function.
...