Activity
From 05/26/2020 to 06/24/2020
06/17/2020
- Hello,
I have a MitySom 5csx and I am trying to run the opencl helloworld program described here:
https://support.criticallink.com/redmine/projects/mityarm-5cs/wiki/MitySOM-5CSX_DevKit_OpenCL_BSP,
The version I want to use is ...
06/04/2020
- Hello,
We used to be able to build preloader in Windows 7 environment. However, not any more after we upgraded to Windows 10. Same u-boot package and same build procedures. So we think the OS change might be the course for the failur...
06/03/2020
- JC 06:47 PM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: GPIO toggling/chattering while performing NAND read.
- Worked on this with Zafer. Posting this to tie up the public post.
The solution to this is to pinmux the gpio0_27 pin in the MLO as a gpio.
Note that all the AD pins will be driven as outputs during the ROM bootloader. This can n...
05/28/2020
- JC 05:19 PM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: GPIO toggling/chattering while performing NAND read.
- Zafer Elbi wrote:
> Have you had any chance to create the problem on your side, I mean since the discussion started?
> ...
Sorry, a few fires came up and this got forgotten. We are currently looking to see if we can get the resources ...
05/27/2020
- ZE 07:12 PM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: GPIO toggling/chattering while performing NAND read.
- Have you had any chance to create the problem on your side, I mean since the discussion started?
ZE
From: Elbi, Zafer
Sent: Tuesday, May 26, 2020 4:04 PM
To: 'redmine@criticallink.com' <redmine@criticallink.com>
Subject: RE: [ARM ... - DR 03:33 PM MitySOM-5CSX Altera Cyclone V FPGA Development: RE: FPGA programming problems
- I will do that.
Thank you very much Dan.
Dario - DV 02:33 PM MitySOM-5CSX Altera Cyclone V FPGA Development: RE: FPGA programming problems
- Hi Dario,
You could also try using the "sync" linux command after you copy the rbf over. That should flush anything out to the SD card. I normally do a sync and a reboot after updating the RBF. Seeing as the filesystem is read/write d... - DR 02:15 PM MitySOM-5CSX Altera Cyclone V FPGA Development: RE: FPGA programming problems
- Hi Dan,
Don't worry, I really appreciate your help.
Yes, running “reboot” works and it is the only way to change the FPGA configuration without rebooting the system multiple times. Indeed, even if I change the rbf and then I turn the ... - DV 12:53 PM MitySOM-5CSX Altera Cyclone V FPGA Development: RE: FPGA programming problems
- Hi Dario,
My apologizes for the later reply, it was a long holiday weekend in the states.
So by running "reboot" after copying over the RBF fixed your problem?
Dan
05/26/2020
- ZE 08:05 PM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: GPIO toggling/chattering while performing NAND read.
- Yes, exactly. We did that test before.
It doesn’t show up in 2013, but shows in 2018.
Thanks
From: redmine@criticallink.com <redmine@criticallink.com>
Sent: Tuesday, May 26, 2020 3:36 PM
Subject: [ARM Cortex-A8 Based Products - So... - JC 07:36 PM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: GPIO toggling/chattering while performing NAND read.
- Zafer Elbi wrote:
> Hello,
> ...
Hi Zafer, just to confirm that the 2013.10 u-boot doesn't chatter but the 2018 one does? - ZE 06:47 PM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: GPIO toggling/chattering while performing NAND read.
- Hello,
The last post was about 2 months ago. I am having exactly the same problem.
Our environment uses previous mityARM board (with single DDR2 version).
Before continuing further, I wondered if there has been any progress.
I teste...