Project

General

Profile

NAND Flash

Added by Marcin Grzelak almost 5 years ago

Hello,
I have a board based on MityDSP-L138 with 4 Gb NAND Flash (MT29F4G08ABADAWP). And I use MityDSP-L138 u-boot (U-Boot 2009.11). But I probably have problem with ECC calculation. After some time during booting I get message:

Verifying Checksum ... Bad Data CRC

ERROR: can't get kernel image!

Do you have any ideas what exactly is wrong?


Replies (6)

RE: NAND Flash - Added by Jonathan Cormier almost 5 years ago

Please attach a complete boot log. And the output of 'printenv'

RE: NAND Flash - Added by Marcin Grzelak almost 5 years ago

Boot log

OMAP-L138 initialization passed!
Booting TI User Boot Loader
        UBL Version: 1.65
        UBL Flashtype: NAND
Starting NAND Copy...
Valid magicnum, 0x55424CBB, found in block 0x00000006.
   DONE
Jumping to entry point at 0xC1080000.

U-Boot 2009.11-svn (cze 19 2019 - 11:54:40)

I2C:   ready
DRAM:  128 MB
NAND:  512 MiB
MMC:   davinci: 0
Bad block table not found for chip 0
Bad block table not found for chip 0
Bad block table written to 0x00001ffe0000, version 0x01
Bad block table written to 0x00001ffc0000, version 0x01
In:    serial
Out:   serial
Err:   serial
error reading I2C Configuration Block
 Error - unable to probe SPI flash.
ARM    Clock : 399360000 Hz
DDR    Clock : 145920000 Hz
EMIFA  CLock : 99840000 Hz
DSP    Clock : 399360000 Hz
ASYNC3 Clock : 199680000 Hz
Enet  config : 0
MMC 0 Enable : 0
Net:   No ETH PHY detected!!!

Hit any key to stop autoboot:  0

Loading from nand0, offset 0x200000
   Image Name:   Linux-2.6.34-rc1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1429428 Bytes =  1.4 MB
   Load Address: c0008000
   Entry Point:  c0008000
## Booting kernel from Legacy Image at c0700000 ...
   Image Name:   Linux-2.6.34-rc1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1429428 Bytes =  1.4 MB
   Load Address: c0008000
   Entry Point:  c0008000
   Verifying Checksum ... Bad Data CRC
ERROR: can't get kernel image!

printenv

bootargs=mem=32M@0xc0000000 mem=64M@0xc4000000 console=ttyS0,115200n8 ubi.mtd=5,2048 root=ubi0:rootfs rootfstype=ubifs rootflags=sync
bootcmd=nboot 0xc0700000 0 0x200000; bootm 0xc0700000
bootdelay=1
baudrate=115200
bootfile="uImage" 
flashuboot= mw.b 0xC0700000 0xFF 0x40000; loady 0xC0700000 115200; nand erase 0xc0000 0x40000; nand write 0xC0700000 0xc0000 0x40000;
flashkernel= mw.b 0xC2000000 0xFF 0x400000; loady 0xC2000000 115200; nand erase 0x200000 0x200000; nand write 0xC2000000 0x200000 0x200000;
flashrescue= mw.b 0xC2000000 0xFF 0x3000000; loady 0xC2000000 115200; nand erase 0x400000 0x400000; nand write 0xC2000000 0x400000 0x400000;
autoload=no
mtdids=nand0=nand
mtdparts=mtdparts=nand:128M(rootfs),-(userfs)
bootargsbase=mem=96M console=ttyS1,115200n8
flashargs=setenv bootargs ${bootargsbase} ${mtdparts} root=/dev/mtdblock0 rw,noatime rootfstype=jffs2
rescue=set bootargs initrd=0xc4000000,4174336 console=ttyS0,115200n8; nand read 0xc4000000 0x400000 0x400000; nboot 0xc0700000 0 0x200000; bootm 0xc0700000
stdin=serial
stdout=serial
stderr=serial
ver=U-Boot 2009.11-svn (cze 19 2019 - 11:54:40)

Environment size: 1116/131068 bytes

RE: NAND Flash - Added by Jonathan Cormier almost 5 years ago

Could you provide all the information on the barcode located on the module? Serial number, model number, etc.

It looks like you have a custom version of the UBL and u-boot.

Some oddities are that your clocks are non standard. U-boot is complaining about missing the NOR. And we don't recommend booting u-boot and kernel from the nand. They should be stored in the NOR.
See our architecture page.
https://support.criticallink.com/redmine/projects/arm9-platforms/wiki/MityDSP-L138_Architecture#Non-Volatile-Storage

UBL Flashtype: NAND
Starting NAND Copy...

I'm also confused how you managed to load the UBL from nand. This is not a boot mode we support.

We also don't recommend using the 2.6 kernel for new designs.

RE: NAND Flash - Added by Marcin Grzelak almost 5 years ago

This is not SOM. But our module, similar to the MityDSP-L138 only with one memory (NAND) and we use the U-Boot 2009.11.

I am looking for information about what may be the cause of wrong ECC calculation. Can I path this u-boot or use a different version?

Thank you for your advice.

RE: NAND Flash - Added by Bob Duke almost 5 years ago

Marcin,

If you are using a Critical Link product in your design we are happy to help in this forum. From your comments, it looks like you are not using a Critical Link product. Our U-Boot is customized for our specific SOM. I would not recommend it for a different design.

TI's Processor SDK would be a better starting point <http://www.ti.com/tool/PROCESSOR-SDK-OMAPL138> .

If you have questions about a custom design based on the OMAP-L138, you should direct your questions to TI's e2e forum <https://e2e.ti.com/> .

Thanks,

-Bob

RE: NAND Flash - Added by Marcin Grzelak almost 5 years ago

OK, I will try with TI's Processor SDK.
Thank you for your time.
Best regards

    (1-6/6)
    Go to top
    Add picture from clipboard (Maximum size: 1 GB)