Activity
From 02/20/2012 to 03/20/2012
03/20/2012
- 05:13 PM Software Development: RE: console redirection
- Hi Scott,
For the kernel, you should only need to change the console argument in the bootargs (assuming the pinmux... - 05:13 PM Software Development: RE: console redirection
- Hi Scott,
For the kernel, you should only need to change the console argument in the bootargs (assuming the pinmux... - Hello,
We are using a MItyDSDPL138 with the MityDSP baseboard. We want to use uart1 on the baseboard to interface w... - 07:34 AM Software Development: RE: StarterWare question ...
- Hello,
Thank you for starting this thraed, because I'm facing the same problem as Tim had 2 weeks ago - *and unfor...
03/19/2012
- 10:30 AM Software Development: RE: 'Fast Boot' DSP
- Is the DSP going to be communicating to the ARM via DSPLINK? If so, this may be a challenge as the ARM and DSP need ...
03/15/2012
- 10:49 PM Software Development: RE: OMAP GPIO
- Hi Mike,
It turns out I didn't enable the Industrial Board I/O option in the kernel. After I enabled it (and enabl... - 08:10 PM Software Development: RE: OMAP GPIO
- Hi Simon,
I don't see anything wrong here, but you might want to ensure that the pin-mux configuration is setup fo... - Hi,
I'm having trouble accessing the OMAP GPIO pins as detailed in the "MityARM-1810 PROFIBUS Dev Kit" documentati... - (Posted on behalf of a customer):
We need to boot the DSP fast (up and running code in less than 2 secs. ) and the...
03/13/2012
- 04:25 PM Software Development: RE: ftdi usb to serial drivers
- Thanks Mike that worked.
- 12:07 PM Software Development: RE: ftdi usb to serial drivers
- You need to install mkimage on your linux machine....
- 12:02 PM Software Development: RE: ftdi usb to serial drivers
- Tim,
Thanks for the help. I see the source in the code tree and also see why I couldn't see it in menuconfig. My p...
03/12/2012
- 05:25 PM Software Development: RE: ftdi usb to serial drivers
- Scott
The FTDI serial drivers should be in the kernel source tree (as of kernel v 2.6.31)
Its the "USB FTDI Single ... - Hello,
I want to access a device across the host USB that uses a FTDI chip to transmit serial data across the usb. ...
03/06/2012
- 04:10 PM Software Development: RE: StarterWare question ...
- Also, as a followup question, the StarterWare examples are setting up the system for the evmOMAPL138. For instance, ...
- (posted on behalf of a customer)
For the starterware non-os method, I have built some of the starterware examples ... - 10:16 AM Software Development: RE: Critical Link Package locations?
- At the moment, we don't provide customized packages. The mityomapl138 location was generated during the bitbake buil...
- (posted on behalf of a customer)
What are the updated feed addresses for the critical link packages?
(these ar...
03/04/2012
- 06:11 PM Software Development: RE: about boot
- Mike,
Thank you very much. I understand. - 04:51 PM Software Development: RE: about boot
- The EXT_BOOT# signal drives a small mux circuit on the SOM that changes the boot strap pull-up/pull-down options on t...
- 04:56 PM PCB Development: RE: FPGA no-connects for 45 size FPGA on MityDSP-L138F
- The bare board PCB for the two variants of the SOM are identical, the only difference is the BOM used for assembly. ...
03/01/2012
- I wonder how the boot mode switch from SPI1 to UART1 using EXT_BOOT# signal? Thank very much.
02/28/2012
- (Posted on behalf of a customer)
We have done a design using the MityDSP-L138F SOM. I tried avoiding using the pin...
02/22/2012
- 05:01 PM Software Development: RE: Hello World Starter Guide Permission Issue
- You rock! It was the file that was the problem. I found the executable and it worked. Thanks!
- 04:50 PM Software Development: RE: Hello World Starter Guide Permission Issue
- Hi Tim,
First, the reason you're getting the "-sh: ./hello.o: Permission denied" error is because the file you are... - I am a newbie to the arm environment and quite green on linux as well. I have been going through the hello world exa...
Also available in: Atom
Go to top
