Project

General

Profile

Activity

From 10/26/2013 to 11/24/2013

11/23/2013

03:34 PM FPGA Development: RE: JFFS2 driver errors
You can do it in the DSP using tcDspSyscfg::SetMasterPriority() in the dsp core library.
-Mike
Michael Williamson
01:30 PM FPGA Development: RE: JFFS2 driver errors
Thanks for those suggestions, Mike. According to Table 11-2, the default priority for EDMA is 0 (highest) and for AR... Steven Hill
08:40 AM FPGA Development: RE: JFFS2 driver errors
Hi Steven,
Is the DMA priority configured higher than the ARM data access priority in the Master Priority Configur...
Michael Williamson

11/22/2013

11:12 PM FPGA Development: JFFS2 driver errors
I'm seeing some errors similar to those mentioned in the following thread:
http://support.criticallink.com/redmine/b...
Steven Hill

11/21/2013

07:14 AM Software Development: RE: Compiling the HelloWorld application with CGT
You should dump out the full build texts between the two operations and compare.
I suspect that the memory configu...
Michael Williamson

11/18/2013

08:43 PM Software Development: Compiling the HelloWorld application with CGT
Hi,
I was trying to compile the DSP HelloWorld Application available at the following location. http://support.cri...
Prashant Dabholkar
11:58 AM Software Development: RE: EDMA conflict DSP <-> Linux
Hej Mike,
I just checked the master priorities. I changed it to the following values:
> 0: EDMA3_0_TC0
> 1: DSP ...
Benedikt K.
10:42 AM Software Development: RE: EDMA conflict DSP <-> Linux
The reservation of resource may be non-sense, but the resources specific to device drivers (like McASP channel queues... Michael Williamson
09:54 AM Software Development: RE: EDMA conflict DSP <-> Linux
The bug was in the param-sets of the edma which were not set correctly in my application.
But now I have another i...
Benedikt K.
10:06 AM Software Development: RE: Linux startup with app running after boot
Steven,
Once you have your program output going to stdout, you can redirect it to a file that can be viewed after ...
Bob Duke
09:31 AM Software Development: RE: Linux startup with app running after boot
You should be using normal stdout printf's in your program and not opening the serial port. Jonathan Cormier

11/16/2013

08:13 PM Software Development: RE: Linux startup with app running after boot
I was wrong about starting the app with the full pathnames for both the app and the DSP executable. I wrote a servic... Steven Hill

11/15/2013

07:26 PM Software Development: RE: Linux startup with app running after boot
Thanks for that, but how do you do the same thing with a systemd service? My filesystem is using systemd for startup. Steven Hill
06:30 PM Software Development: RE: Linux startup with app running after boot
Steven
In your script that runs the app, just "cd" to the correct directory. I.e.
cd /mnt/user_nand
./myApp mydspE...
Tim Iskander
06:27 PM Software Development: RE: Linux startup with app running after boot
I have what might seem like a dumb question. I like the idea of starting the app as a service, and I have written an... Steven Hill

11/12/2013

02:33 PM Software Development: RE: EDMA conflict DSP <-> Linux
Was the bug in the kernel or your application? Jonathan Cormier
02:09 PM Software Development: RE: EDMA conflict DSP <-> Linux
Found the reason. The DMA configuration was wrong. Benedikt K.
07:59 AM Software Development: RE: Linux startup with app running after boot
Steven
One other note..
If you are using a newer filesystem with systemd (does /etc/systemd exist) things are a bit...
Tim Iskander
07:52 AM Software Development: RE: Linux startup with app running after boot
Steven
1 - No you don't need to log in as root... the init system will run your script for you. One thing that may...
Tim Iskander

11/11/2013

08:28 PM Software Development: Linux startup with app running after boot
I am at the final stage in getting my project working on the MityDSP L138 board. I want to load the FPGA control mod... Steven Hill

11/09/2013

06:06 PM Software Development: RE: EDMA conflict DSP <-> Linux
Hej Mike,
I'm using my own board and also my own baseboard-configuration.c which is based on your baseboard-indust...
Benedikt K.

11/08/2013

01:56 PM Software Development: RE: EDMA conflict DSP <-> Linux
What baseboard file are you using?
The devkit one configures MCASP for use by the ARM/linux. Could be a resource ...
Michael Williamson
09:47 AM Software Development: EDMA conflict DSP <-> Linux
Hej,
I try to use the EDMA to copy data from the McASP to and from a buffer for further processing on the DSP.
...
Benedikt K.

11/05/2013

10:37 AM Software Development: RE: How to launch application on startup
... Bob Duke
09:55 AM Software Development: RE: How to launch application on startup
So, from the command line:... Mary Frantz
07:05 AM FPGA Development: RE: uPP receive issues
Yes, this is the issue. The pin-muxed OMAP-L138 net that includes the UPP_CHB_CLOCK is not connected to a GCLK pin. ... Michael Williamson
06:18 AM FPGA Development: RE: uPP receive issues
I have resolve that problems. Maybe I was wrong to select uPP clock sources (PLL1_SYSCLK2).
But, when my FPGA syte...
minh tung

11/04/2013

01:09 PM Software Development: RE: How to launch application on startup
Mary,
When you exit a shell, all processes connected to the shell are typically terminated. When you execute a sc...
Bob Duke
12:54 PM Software Development: RE: How to launch application on startup
Do you happen to know if your system is using systemd for starting processes?
You can check to see if the followin...
Jonathan Cormier
12:48 PM Software Development: RE: How to launch application on startup
You can run the command "ps | grep myApplication" and look for your process in order to tell if its running.
Also ...
Jonathan Cormier
12:44 PM Software Development: RE: How to launch application on startup
Mary,
I think you have a typo here:
./home/root/HelloWorldDSP/Debug/myApplication myArgument &
There shouldn't b...
Jonathan Cormier
12:41 PM Software Development: How to launch application on startup
Could you provide an example of how to start an application on startup. I get that you can run it from a script in i... Mary Frantz
 

Also available in: Atom

Go to top
Add picture from clipboard (Maximum size: 1 GB)