Project

General

Profile

Activity

From 09/18/2014 to 10/17/2014

09/26/2014

02:27 AM Software Development: RE: GP0[4] state on boot for L138F
??How quickly do you need it to be low? You might put an external pull down on your board.??
Pretty much instantly...
Mostafa Afgani

09/25/2014

07:46 PM Software Development: RE: GP0[4] state on boot for L138F
How quickly do you need it to be low? You might put an external pull down on your board.
You could disable the pu...
Michael Williamson
05:11 PM Software Development: RE: GP0[4] state on boot for L138F
Hi Mike, thanks for the explanation. As we need this pin to be low on power-up, would the best place to set this be i... Mostafa Afgani
03:40 PM Software Development: RE: GP0[4] state on boot for L138F
Hi,
If you check the OMAP-L138 datasheet (it's a bit convolved) Table 2-29, the GP0[4] pin pullup state is defined...
Michael Williamson
03:28 PM Software Development: GP0[4] state on boot for L138F
Hi, we noticed that the power on state of GPIO_0_4 is that it is driven high. I am a little confused about this since... Mostafa Afgani

09/23/2014

02:05 PM Software Development: RE: UPP problem
Problem was caused by cache incoherency. Use of BCACHE_inv() fixed it. stephan berner

09/22/2014

10:19 AM Software Development: RE: USB Bug
There are several missing features in the 3.14 branch that I found when trying to move to it. I created a tag to mark... Jonathan Cormier
10:13 AM Software Development: RE: USB Bug
Note that we have seen a similar issue on the 335x. Could you checkout the following page and report back if the solu... Jonathan Cormier
10:11 AM Software Development: RE: USB Bug
It is from your git page - as far as I remember. Our software student tried to jump to 3.14 two month ago but it didn... Benedikt K.
09:39 AM Software Development: RE: USB Bug
Hello,
Are you using a 3.7 branch from our git site, or the mainline? I don't think we officially support 3.7. D...
Michael Williamson
09:37 AM Software Development: RE: USB Bug
Another thing: When I plug in the first usb device the number of usb interrupts in /proc/interrupts increases. When I... Benedikt K.
09:22 AM Software Development: USB Bug
Hej hej,
we have noticed a usb bug on the MityDSP and we are not sure why this happens.
We are using linux 3.7....
Benedikt K.

09/21/2014

02:51 PM Software Development: UPP problem
hi,
I am having problems reading data from the FPGA to memory. I set up the UPP interface
using channel A from t...
stephan berner

09/18/2014

10:07 AM FPGA Development: RE: Mity L138F FPGA -> OMAP interrupt lines
Thanks Mike,
I have found the pin mapping for INT0 and INT1 I couldn't find the mapping for the Non Maskable Inte...
Christopher Brunson
09:48 AM FPGA Development: RE: Mity L138F FPGA -> OMAP interrupt lines
Hi Chris,
The information you need is in Table 4 of the "Carrier Board Design Guide":http://www.criticallink.com/w...
Michael Williamson
09:36 AM FPGA Development: Mity L138F FPGA -> OMAP interrupt lines
I was trying to use an FPGA interrrupt which should be serviced by the DSP core in the OMAP.
From the MityL138.ucf...
Christopher Brunson
 

Also available in: Atom

Go to top
Add picture from clipboard (Maximum size: 1 GB)