Project

General

Profile

Activity

From 02/18/2020 to 03/18/2020

03/16/2020

03:58 PM Software Development: RE: GPIO toggling/chattering while performing NAND read.
Note the pinmux tables can be read from memory.
See "Table 9-10: CONTROL_MODULE REGISTERS" https://support.critic...
Jonathan Cormier
03:35 PM Software Development: RE: GPIO toggling/chattering while performing NAND read.
Hi,
Thank you for your input.
Tried with below command, still same problem.
mw.w 0x50000078 48
As mentione...
Srinivasa Wunnimani
02:09 PM Software Development: RE: GPIO toggling/chattering while performing NAND read.
> md.b 0x50000070 10
> mw.b 0x50000078 48
> mw.b 0x50000079 00
I would stick with using md.w and mw.w since all ...
Jonathan Cormier

03/14/2020

11:52 AM Software Development: RE: GPIO toggling/chattering while performing NAND read.
Sorry for typo error:
I was able to manual write it to GPMC *without* any error.
Regards
Srinivasa
Srinivasa Wunnimani
08:47 AM Software Development: RE: GPIO toggling/chattering while performing NAND read.
Hi,
I tried to change GPMC_CONFIG7_0 to 0x48 from 0xf48 as below. I was able to manual write it to GPMC with any ...
Srinivasa Wunnimani

03/11/2020

01:41 PM Software Development: RE: GPIO toggling/chattering while performing NAND read.
You can use md to read memory locations and mw to write them. https://www.denx.de/wiki/publish/DULG/to-delete/UBootCm... Jonathan Cormier
11:13 AM Software Development: RE: GPIO toggling/chattering while performing NAND read.
Hi,
Manually means, do you want me to change GPMC_CONFIG7_0 at u-boot prompt?
Regards
Srinivasa
Srinivasa Wunnimani
10:45 AM Software Development: RE: GPIO toggling/chattering while performing NAND read.
Hi,
With u-boot V2013 frequency of pulses @ ~3.571 MHz and amplitude ~150 mV.
With u-boot V2018 frequency of puls...
Srinivasa Wunnimani

03/09/2020

03:02 PM Software Development: RE: GPIO toggling/chattering while performing NAND read.
If you manually set GPMC_CONFIG7_0 back to 48, does the activity on GPIO 0_27 stop?
Jonathan Cormier
02:27 PM Software Development: RE: GPIO toggling/chattering while performing NAND read.
Srinivasa,
We have not seen this before and I am reviewing your comments and logs.
Diff of GPMC registers...
Bob Duke
01:23 PM Software Development: RE: GPIO toggling/chattering while performing NAND read.
Hi,
I have dumped the values of GPMC registers for u-boot V2013.10 and V2018 at u-boot prompt. Please find the fi...
Srinivasa Wunnimani

03/06/2020

12:08 PM Software Development: RE: GPIO toggling/chattering while performing NAND read.
Hi,
Test case 1:
Tested on u-boot Version 2013.10 from mitysom (u-boot-mityarm-335x-6c6a700.tar.gz).
Probed GPIO...
Srinivasa Wunnimani
07:25 AM Software Development: GPIO toggling/chattering while performing NAND read.
Hi,
We have mitySOM board in our product and we are using u-boot-mityarm-335x.tar.gz and building u-boot as below:...
Srinivasa Wunnimani

02/18/2020

02:37 PM Software Development: RE: Reading contents of a file in Uboot
u-boot doesn't really have a lot of file io ability.
You can load a file from sd card, tftp, nfs, or nand into m...
Jonathan Cormier
11:01 AM Software Development: Reading contents of a file in Uboot
Hi ,
How can i read or cat contents of file from uboot.
Regards,
manjunath
Manjunath K S
 

Also available in: Atom

Go to top
Add picture from clipboard (Maximum size: 1 GB)