Activity
From 05/20/2013 to 06/18/2013
06/18/2013
- 08:50 PM MityDSP (TI TMS320C6xxx Based Products) Software Development: RE: Mitydsp Pro compile and link errors
- Hmm.
We'll look some more tomorrow, but the '--define="CHIP_6711"' option to the compiler should not be set for th... - Downloaded MityDSP 2.12 and installed.
Using CCSv5.1.0.09.
Imported C:\MityDSP\2.12\software\demo\CCSV5\UDP_echo pr...
06/14/2013
- 06:52 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: DSPHelloWorld won't compile
- I don't see any errors in the console.txt. Maybe eclipse has something cached and is showing errors that aren't curr...
- 06:15 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: DSPHelloWorld won't compile
- To Dave Stehlik: Most of the errors disappeared when I fixed the error in the Message() functio, but I am still left...
- 06:08 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: DSPHelloWorld won't compile
- I'm replying to my own post - I found a problem with the lpMessageOutbound->SendMessage function. When I changed the...
- 06:03 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: DSPHelloWorld won't compile
- Hello Steven,
I am going to assume that you have an error indicating that it can't locate an include file,
say st... - 05:51 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: can't detect USB2.0 device
- Not sure why the 3.2 kernel is causing problems for you. It could be that you need to recompile our 3.2 kernel branc...
- 05:47 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: DSP Hello World error message
- Sorry for the delay.
I have seen these messages before, but we have several applications that do not exhibit this ... - 05:45 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: omap driver & rs485
- The omap driver is modified for the MityARM-3359 (the AM335X SOC chips). This patch actually came from support of ou...
- 04:35 PM MityDSP-L138 (ARM9 Based Platforms) FPGA Development: RE: Issues programming FPGA using Linux driver
- Thanks for the quick reply!
I am indeed using a BIN file. It is entirely possible that it is not bit-swapped, it was... - 03:57 PM MityDSP-L138 (ARM9 Based Platforms) FPGA Development: RE: Issues programming FPGA using Linux driver
- If you are not using the framework, the state sysfs value will report FAIL (I think it is checking the version of the...
- I am trying to program the LX45 FPGA on my MityDsp board using the fpga_ctrl.ko driver but don't have much luck.
Eve...
06/13/2013
- I am trying to compile the ARM part of DSPHelloWorld in Eclipse. Compile of arm_main is failing for really basic stu...
- Hi,
I've some questions about your patch from this link : http://support.criticallink.com/redmine/projects/armc8-p...
06/12/2013
- 02:15 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: SATA disk can‘t be linked when booting the linux kernel (Using industrial board)
- Thanks for answering me so quickly, the S/N number of my MITY-AM1808 is: 121470. I will also try some other sata disk...
06/11/2013
- 08:02 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: DSP vs NEON for Floating point
- Sorry, my bad. I see it now. The first time I tried the SDK it didn't work as I didn't install the whole 4GB of stuff...
- 07:28 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: DSP vs NEON for Floating point
- Hello Conor,
On the DVSDK, the examples in c6run include a "hello world" (ti-dvsdk_omapl138-evm_04_03_00_06/c6run_... - 06:26 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: DSP vs NEON for Floating point
- Just in addition - it would kinda cool to have a "Hello world" done using the TI DVDSK as it has the command line DSP...
- 07:37 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: SATA link down
- Just following up, are you still having problems?
-Mike
- 06:32 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: SATA disk can‘t be linked when booting the linux kernel (Using industrial board)
- Hello,
Thank you for your post. I have not heard back from yilan wang, and I was assuming that his issue was reso... - When I use industrial board 000268RI-2B and mityARM-1808 to do some development, I'v meet the same problem with "yili...
06/10/2013
- 11:12 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Noise on the Can Bus Interface
- Hi Jeremy,
Sorry we didn't respond right away. We were trying to find someone to look at the issue and set someth... - 11:06 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Noise on the Can Bus Interface
- I figured out where the dropped frames were going. It appears the noise is being sufficiently taken care of when the ...
06/07/2013
- When (in the DSP Hello World) the arm calls ldDspApp0>StopApp(), I receive an error message (at the bottom of this po...
06/06/2013
- 04:41 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Warning messages when running DSP Hello World
- I'm getting the same thing...
- 04:29 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: DSP vs NEON for Floating point
- Digikey is open but managers' pockets are closed most of the time!
My circuit design is in flux still but I'm at t... - 11:39 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: DSP vs NEON for Floating point
- Digikey is open 24 hours a day!
Do you have a lot of interfaces to rework if you retarget your module?
-Mike
... - 11:28 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: DSP vs NEON for Floating point
- Thank you for that Mike. I'm trying to figure out is it worth the pain of learning the DSP toolsets and dealing with ...
- 09:47 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: DSP vs NEON for Floating point
- The DSP floating point performance is *very good* compared to the ARM9. It's actually faster (when coded right) than...
- Dear Critical Link,
Now that you have newer modules in Cortex A8 and Dual A9 versions, I have a question as regard... - I have measured a significant 500kHz noise burst on the CAN bus pins of the Industrial IO board. the reason for check...
06/05/2013
- 01:08 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Can Interface won't probe
- Okay, I had wiring problem. candump now dumps the received frames to the console. So we are up and running. thanks fo...
- 12:33 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Can Interface won't probe
- Can you dump out the exact commands you used?
Thanks. (I am not a CAN expert, but I can try to track down the eng... - 12:27 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Can Interface won't probe
- Well, Although the kernel now sees the CAN controller the ifconfig -a reads all zeros for everything even after I app...
- 11:26 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Can Interface won't probe
- I applied the patch to the 3.2 kernel and it is now up and running. I will now check the the functionality with the c...
- 11:00 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Can Interface won't probe
- I am dead in the water at the moment. I will try the patch set on the 3.2 kernel and let you know how it goes.
- 10:23 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Can Interface won't probe
- Hello,
I've pushed a "patch set":http://support.criticallink.com/gitweb/?p=linux-davinci.git;a=commit;h=c008e4e8bb... - 07:31 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Can Interface won't probe
- Hello Mr. Young,
I have reproduced the issue here. There are some patches that never made it to our external git ...
06/04/2013
- 01:51 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Can Interface won't probe
- The only other thing is I have your rs485 converter card plugged into the expansion port for UART2
- 01:44 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Can Interface won't probe
- The revision # is 80-000268RI-2B
I downloaded the latest release today and compiled the kernel with out the audio ... - 01:35 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Can Interface won't probe
- Can you please send me the revision of the board you are working with (there should be an 80- number somewhere on the...
- 01:01 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Can Interface won't probe
- It is just the eth0 and lo entries. there is no can0 entry. the probe fails on boot up.
- 12:07 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Can Interface won't probe
- Can you dump the text of "ifconfig -a"?
-Mike - 12:06 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Can Interface won't probe
- In case it is important I am using the Am1810 with the industrial IO board. I have tried both Linux branches and they...
06/03/2013
- I get the following dmesg about the MCP251x not working,
MCP251x didn't enter in conf mode after reset
Is there...
06/02/2013
- 07:11 AM MitySOM-335x (ARM Cortex-A8 Based Products) PCB Development: RE: MityArm 335x Minimum Voltage Operation
- Hello Mr. Schantzen,
Very sorry for the delay in response.
We are looking into this spec, because at first gl... - 07:03 AM MitySOM-335x (ARM Cortex-A8 Based Products) PCB Development: RE: VSC8601/VSC8641 PHY Discontinued
- Hi Michael,
Yes, we have also seen this notification. It doesn't look like there is a drop-in replacement in the ...
05/31/2013
- Vitesse just announced the VSC8601/VSC8641 part will be discontinued. Are there alternative PHYs that can be used?
- I'm using a USB 2.0 ethernet adapter with mityARM-1808.
It works good in 2.6.34.rc1 kernel but bad in 3.2.0.
I do a...
05/30/2013
- 08:50 AM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: Difficulty in flashing MLO and U-Boot to the AM3354 with 512MB NAND
- Apologies...
I checked the git status before pushing and completely missed the board/cl tree (for some reason I was ... - 08:24 AM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: Difficulty in flashing MLO and U-Boot to the AM3354 with 512MB NAND
- I encountered an error building branch u-boot-2013.01. Files in board/cl/mityarm335x are missing. Here's the make err...
05/29/2013
- 09:20 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Debugging DSP-App when DSPLink is running
- Hi Christian,
See the last section of http://support.criticallink.com/redmine/projects/arm9-platforms/wiki/DSP_Qu... - Hi all,
what is the usual procedure for debugging the DSP-App when using the DSPLink?
Based on the DSPLink exam... - 03:40 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: U-Boot ELF loader
- Oops, my silly. That now works, it takes the TI CCS image and moves sections to the correct address and runs :)
...
05/28/2013
- 03:44 PM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: Difficulty in flashing MLO and U-Boot to the AM3354 with 512MB NAND
- Finally... I have a u-boot image that will boot from the 512MB (4096k page) NAND.
It is now based on the main-line u... - Hello,
I'm using the UPP on the OMAP-L138F to receive video data that's been buffered by the Xilinx FPGA. The FPGA l... - 11:06 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: U-Boot ELF loader
- Hi Bruce,
Looking at your elf information, it looks like you are loading the ELF image to 0xc0700000, which is rig... - 08:51 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: U-Boot ELF loader
- The above thread has gone a little cold, does anyone know if uboot ELF loader should work with TI Code Composer gener...
05/24/2013
- I am running DSP/BIOS on the DSP and linux on the ARM (MDK_2012-08-10).
The DSP receives data from the McBSP1 via ... - 08:56 AM MityDSP (TI TMS320C6xxx Based Products) Software Development: RE: Problem compling with the MDK, unresolved symbols
- I just get control of 2 of the 3 LEDs (D1 and D2) on the MityDSP-Pro board, by setting the the anValue to 0x0
or 0x... - 08:49 AM MityDSP (TI TMS320C6xxx Based Products) Software Development: RE: Problem compling with the MDK, unresolved symbols
- Most of the I/O is controlled hooked to the FPGA. Do you have an FPGA image programmed (is the RED FPGA programming ...
- 08:41 AM MityDSP (TI TMS320C6xxx Based Products) Software Development: RE: Problem compling with the MDK, unresolved symbols
- Mike,
Thanks a lot for your anwser. But i still dont understand much.
Coule your please give an exemple implementa... - 08:19 AM MityDSP (TI TMS320C6xxx Based Products) Software Development: RE: Problem compling with the MDK, unresolved symbols
- You need to implement a class that derives from the tcDspOutputLatch class. The tcDspOutputLatch is an interface cla...
- 05:48 AM MityDSP (TI TMS320C6xxx Based Products) Software Development: RE: Problem compling with the MDK, unresolved symbols
- It seems ok now with DSP/Bios configuration file added to the project.
But I oberve nothing on the osciloscope. I t... - 04:12 AM MityDSP (TI TMS320C6xxx Based Products) Software Development: RE: Problem compling with the MDK, unresolved symbols
- **** Build of configuration Debug for project testDACoutput ****
"D:\\TI\\ccsv5\\utils\\bin\\gmake" -k all
'Buil... - Hi, I am using the MDK 2.10 with CCStudio v5.3. I tried to complied a test project for the MityDSP-Pro development Ki...
05/22/2013
- 08:18 AM MityDSP-L138 (ARM9 Based Platforms) FPGA Development: RE: FPGA load verification
- Mike,
While troubleshooting the state of the lock status line I did discover there were instances of the clock not... - 08:05 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: SATA link down
- Hi,
Can you confirm that your drive is limited to SATA-II link speeds.
See the "AM1808 Errata":http://www.ti.... - I am attaching SATA SSD drives to MityARM1808.I am using 2.6.x kernel and NFS.My SSD is formated EXT2 with 1 Partitio...
05/21/2013
- 11:14 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Open Embedded Core Process Release Date
- As of right now and the foreseeable future the bitbake process is not working.
Your best options for creating a ... - 10:48 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Open Embedded Core Process Release Date
- Hi,
Sorry for the lack of detail,
I want to setup an Open Embedded/Angstrom build system for a product I'm wor... - 10:47 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Open Embedded Core Process Release Date
- Are you refering to this other post?
http://support.criticallink.com/redmine/boards/10/topics/2573?r=2707
It appe... - 10:39 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Open Embedded Core Process Release Date
- Kevin,
Have you seen this page [[Starter_Guide]]?
Also we just released a new MDK that contains an updated kern... - Hi,
I'm trying to build a MityDSP Image from the currently released information/files without success,
I reali... - 05:30 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: U-Boot ELF loader
- Mike, thanks for your reply.
I tried lminfo and it doesn't recognise the image. I attach a log of the u-boot comm...
05/20/2013
- 09:39 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: ethernet over USB don't work
- My problem is solved now.
Thanks a lot. - 08:45 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: U-Boot ELF loader
- You may need to provide an "entry point" argument to the linker to point to the location in memory that the code shou...
- 08:17 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: U-Boot ELF loader
- Jonathan,
Thanks for pointing me in the right direction. I have downloaded the latest MDK and installed u-boot. Th...
Also available in: Atom
Go to top
